Filter
Top Products
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
20
Adjusting the color convergence
This projection TV uses three separate TV tubes: red, green, and blue.
The red, green, and blue images are projected onto the screen where
they converge to form a full-color picture. You can see a clear picture
only when the three images converge correctly. Convergence may drift
over time or if the TV is moved. If you can see clear images on the
screen, skip this procedure.
Make this adjustment after the TV has been on for at least 30
minutes.
To check and adjust the color convergence:
1. Press MENU, then press x or • until the PICTURE menu
appears.
2. Press y or z to highlight CONVERGENCE (see illustration
below left).
3. Press x or • to display the center CONVERGENCE menu (see
illustration below right).
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
2 3 4 5 6 7 8 9 10 11 12 1314 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
12345678910111213141516171819
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
P CTURE ANTENNAI
MODE SPORTS
PREFERENCE
FLESH TONE ON
OFF
COOL
NOI REDUCTIONSE
CONVERGENCE
SAVE NEW
COLOR
TEMPERATURE
12345678910111213141516171819
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
12345678910111213141516171819
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
EXIT TO SELECT POSI IONT:
ENTER
RED BLUE
TO SELECT COLOR:
If you see separate red, blue, or green crossed lines (or red or blue
shadows next to white lines), you need to adjust the convergence.
4. Press ENTER to highlight RED or BLUE, depending on which
color needs adjusting. If both red and blue need adjusting,
perform steps 4 and 5 twice.
5. Press y (up), z (down), x (left), or • (right) on the remote
control to converge the red or blue line into the green line, which
will turn completely white when correctly adjusted. When color
convergence is correctly adjusted, you will see two single white
lines.
6. Press EXIT to close the center CONVERGENCE menu and
open the circumference CONVERGENCE menu (see
illustration below left).
7. Press the corresponding Number button (1–4 and 6–9) to select
the area to adjust.
8. Press ENTER to highlight RED or BLUE (see illustration below
right), depending on which color needs adjusting. If both red and
blue need adjusting in the selected area, perform steps 8 and 9
twice.
12345678910111213141516171819
20 21 22 23 24 25 26 27 28 29 30 31 32 3
3
12345678910111213141516171819
20 21 22 23 24 25 26 27 28 29 30 31 32 3
3
PUSH 1
8
2
9
3
6
7
1
4
9–
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
2 3 4 5 6 7 8 9 10 11 12 1314 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
12345678910111213141516171819
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
RED BLUE
EXIT TO SELECT POSI IONT:
ENTER TO SELECT COLOR:
9. Press yzx • to converge the red or blue line into the green line,
which will turn completely white when correctly adjusted. Repeat
steps 8 and 9 until you see two single crossed white lines.
10. Press EXIT once to select another area to adjust, and then repeat
steps 7–9.
11. Press EXIT twice to close the CONVERGENCE menu.
TV
CABLE
VCR
12
3
45
6
7
8
9
100
0
ENT
POWER
MUTE
CH RTN
RECALL
CH
VOL
MENU/
ENTER
VOL
CH
FAV CH
TV/VIDEO
E
I
T
X
EXIT
yzx •
Number
MENU/
ENTER