Filter
Top Products
21-EN
Setting the Treble Control
You can change the Treble Frequency emphasis to create your own tonal
preference.
For iDA-X200, the following setting can be made only when the
IMPRINT audio processor (PXA-H100) is not connected.
1
Press and hold IMPRINT (iDA-X200 only) or
SOUND (iDA-X300 only) for at least 2 seconds to
activate the Audio Selection mode.
2
Turn the Double Action encoder (iDA-X200 only)
or Rotary encoder (iDA-X300 only) to select the
TREBLE Adjustment mode, and then press
/ENTER.
SUBW SUBW SYSTEM
*
BASS TREBLE HPF
SUBW
* Displayed only when subwoofer is ON.
3
-1
*2
Turn the Double Action encoder (iDA-X200 only)
or Rotary encoder (iDA-X300 only) to select the
desired treble level (–7~+7), and then press
/ENTER.
You can emphasize the treble level.
3
-2 Turn the Double Action encoder (iDA-X200 only)
or Rotary encoder (iDA-X300 only) to select the
desired treble center frequency, and then press
/ENTER.
10.0 kHz 12.5 kHz 15.0 kHz 17.5 kHz 10.0 kHz
Emphasizes the displayed treble frequency ranges.
4
Press to return to normal mode.
• If no operation is performed for 15 seconds, the unit will return to
normal mode automatically.
• If is pressed during setting, the unit returns to the previous item.
• The function is inoperable when DEFEAT is set to ON.
*
2
The adjustment can also be made by pressing IMPRINT (iDA-X200
only) or SOUND (iDA-X300 only). Refer to “Adjusting Subwoofer/
Bass/Treble/Balance(Between Left and Right)/Fader (Between Front
and Rear)/Loudness/Defeat” (
page 19).
Adjusting the High Pass Filter
The High Pass Filter on this unit can be adjusted to suit your personal
taste.
For iDA-X200, the following setting can be made only when the
IMPRINT audio processor (PXA-H100) is not connected.
1
Press and hold IMPRINT (iDA-X200 only) or
SOUND (iDA-X300 only) for at least 2 seconds to
activate the AUDIO selection mode.
2
Turn the Double Action encoder (iDA-X200 only)
or Rotary encoder (iDA-X300 only) to select the
HPF Adjustment mode, and then press
/ENTER.
SUBW SUB SYSTEM
*
BASS TREBLE HPF
SUBW
* Displayed only when subwoofer is ON.
3
Turn the Double Action encoder (iDA-X200 only)
or Rotary encoder (iDA-X300 only) to select the
desired HPF frequency, and then press
/ENTER.
OFF 80 (Hz) 120 (Hz) 160 (Hz)
4
Press to return to normal mode.
• If no operation is performed for 15 seconds, the unit will return to
normal mode automatically.
• If is pressed during setting, the unit returns to the previous item.
• The function is inoperable when DEFEAT is set to ON.
Operating the External Audio Processor
You can call up the preset memory of the external audio processor from
this unit.
1
Press and hold PRESET for at least 2 seconds to
call the external audio processor mode when the
external audio processor is connected.
The AP Preset screen is displayed.
2
Turn the Double Action encoder (iDA-X200 only)
or Rotary encoder (iDA-X300 only) to select the
preset number, and press
/ENTER.
• For the operation of external audio processor, refer to the Owner’s
Manual of the external audio processor you purchased.
Setting the Treble Level
Setting the Treble Center Frequency