Filter
Top Products
46-EN
Antenna Receptacle
Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
• This lead should be used only for controlling the vehicle’s power
antenna. Do not use this lead to turn on an amplifier, or a signal
processor, etc.
Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
Audio Interrupt In Lead (Pink/Black)
Illumination Lead (Orange)
This lead may be connected to the vehicle’s instrument
cluster illumination lead. This will allow the backlighting of
the iDA-X200/iDA-X300 to dim whenever the vehicle’s lights
are turned on.
Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle’s fuse
box or another unused power source which provides (+)12V
only when the ignition is turned on or in the accessory
position.
Battery Lead (Yellow)
Connect this lead to the positive (+) post of the vehicle’s
battery.
Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is
securely fastened using the sheet metal screw provided.
Power Supply Connector
Right Front (+) Speaker Output Lead (Gray)
Right Front (–) Speaker Output Lead (Gray/Black)
Right Rear (–) Speaker Output Lead (Violet/Black)
Right Rear (+) Speaker Output Lead (Violet)
Left Rear (+) Speaker Output Lead (Green)
Left Rear (–) Speaker Output Lead (Green/Black)
Left Front (–) Speaker Output Lead (White/Black)
Left Front (+) Speaker Output Lead (White)
Fuse Holder (10A)
Ai-NET Connector
Connect this to the output or input connector of another
device (CD Changer, Equalizer, HD Radio TUNER
MODULE, etc.) equipped with Ai-NET.
• Interface adapter for iPod (KCA-420i) is not recommended for use
with this product.
Steering Remote Control Interface Connector
(iDA-X200 only)
To steering remote control interface box.
Rear Output/Input RCA Connectors (iDA-X200 only)
It can be used as Rear Output or Input RCA Connectors.
RED is right and WHITE is left.
Front Output/Input RCA Connectors (iDA-X200 only)
It can be used as Front Output or Input RCA Connectors.
RED is right and WHITE is left.
Subwoofer Output RCA Connectors (iDA-X200 only)
Front/Subwoofer Output RCA Connectors
(iDA-X300 only)
RED is right and WHITE is left.
Ai-NET Cable (Included with CD Changer)
RCA Extension Cable (sold separately)
iPod Direct Connector
Control iPod signals.
Connect this to an iPod or to an optional Bluetooth Box. To
use a hands-free mobile phone, an optional Bluetooth Box
connection is required. For details on connection, refer to
the Owner’s Manual of the Bluetooth Box.
You can also connect this to an external device (such as a
portable player) by using iPod Direct/RCA Interface cable
(sold separately).
* Refer to “Setting the AUX+ Mode” (page 23).
FULL SPEED™ Connection Cable (KCE-422i) (iDA-
X200 sold separately/iDA-X300 supplied)
System Switch
When connecting a processor or divider using Ai-NET,
place this switch in the EXT AP position. When no device is
connected, leave the switch in the NORM position.
iDA-X200 only:
When switched to NORM, the RCA Connectors and
can be used as Output RCA Connectors.
When switched to EXT AP, the RCA Connectors and
can be used as Input RCA Connectors.
• Be sure to turn the power off to the unit before changing the switch
position.
USB Connector
Connect this to an USB memory (or to an iPod (iDA-X200
only)). To use an iPod, iPod Dock interface cable
connection is required (iDA-X200 only).
• Use the supplied USB cable. If a USB cable other than the supplied is
used, correct performance cannot be guaranteed.
• Route the USB cable away from other cables.
AUX+ ON : When the external device is connected.
AUX+ OFF : When an iPod is connected.
To prevent external noise from entering the audio system.
• Locate the unit and route the leads at least 10 cm away from the car harness.
• Keep the battery power leads as far away from other leads as possible.
• Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.
• If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise
suppressors, contact them for further information.
• Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.