30
5. Dimmer Control
To control the display intensity of the front panel Vacuum Fluorescent
Display (VFD) information window. In case you feel that the display
becomes a distraction to your enjoyment of the video, this option allows
you to dim it or turn it off. The available options are:
On - The VFD window is at normal brightness.
Dim - The VFD window is at reduced brightness.
Off – The VFD window is turned off. In this mode the display resumes
momentarily when there is any user operation.
6. OSD Mode
To select how long the on-screen display information, such as elapsed or
remaining time, stays on the TV screen. The available options are:
Normal – On-screen display information stays on the TV screen until the
user cancels it.
Silent – On-screen display information shows on the TV screen for a few
seconds and then disappears. The front panel display still maintains the
selected display information.
Remaining – On-screen display information stays on the TV screen until
the user cancels it. By default display remaining time instead of elapsed
time.
7. Persistent Storage
Persistent storage is a data storage area that holds additional contents
for BonusView and BD-Live features. The data will be kept even if you turn
off the player. The following persistent storage management options are
available:
Storage Device – To select which storage device should be used as the
persistent storage. The 650BD is equipped with 1GB of internal flash
memory. There are also two USB 2.0 ports on the player that can accept
a USB drive to be used as the persistent storage. The choices are:
Internal Flash – Use the internal flash memory for persistent storage.
USB Drive – Use a USB drive for persistent storage. To meet the
specification for BD-Live, a USB flash drive of 1GB or larger is required. A
USB hard disk is not recommended.
Note: The new storage device choice becomes effective only after the
player is restarted. Please make sure that you turn off the player and then
turn it back on after changing the
"Storage Device" option.
Total Space – To display the total space of the persistent storage.
Available Space – To display the currently available space of the
persistent storage. If the available space becomes too low, some Blu-ray
Discs may not play properly.
Erase BD-Video Data – To erase the BD-Video data from the persistent
storage.
8. Reset Factory Defaults
To reset all settings to the factory default value.
Note: The parental control password and ratings will not be reset. This
operation is only available when the playback is completely stopped or
when there is no disc loaded.
Network Setup
The "Network Setup" section of the Setup Menu system allows you to
configure the parameters for the Internet connection of the player, test
the connection and restrict BD-Live access. The menu items in this
section are:
Menus Settings
IP Configuration............................................Auto
Manual
IP Address
Subnet Mask
Gateway
DNS 1
DNS 2
BD-Live Network Access..............................On
Limited
Off
Connection Test
Mac Address
1. IP Configuration
To determine how the player obtains its IP address. The available options
are:
Auto (DHCP) - The player automatically obtains its IP address information
using DHCP (Dynamic Host Configuration Protocol). This is the default
setting. In most cases, automatic IP configuration can be used.
Manual – Manually enter the numeric IP address information. Set the IP
configuration manually only when the router has no DHCP server
functions or when the router’s DHCP server function is disabled. For more
information on how to manually configure the Internet connection and
what values to use, please consult your broadband router/modem
instruction manuals or call your Internet service provider.
2. IP Address
The Internet Protocol address of the player. When "IP Configuration" is set
to "Auto (DHCP)", the value displayed here is obtained using DHCP and
cannot be changed.
3. Subnet Mask
Each IP address has an associated subnet mask. It is used by the player
to decide whether to route network traffic through the router or directly to
another device on the same network. When "IP Configuration" is set to
"Auto (DHCP)", the value displayed here is obtained using DHCP and
cannot be changed.
4. Gateway
The IP address of the router. It is also called "default gateway" or "default
router". When "IP Configuration" is set to "Auto (DHCP)", the value
displayed here is obtained using DHCP and cannot be changed.
Setup menu continued