Filter
Top Products
15
In case you experience any problem with this unit, please take
the time to look through this chart and see if you can solve the
problem yourself before you call your dealer.
No power
e
Check the connection to the AC power supply. Check and
make sure the AC source is not a switched outlet and that,
if it is, the switch is turned on. Make sure there is power to
the AC outlet by plugging another item such as a lamp or
fan.
e
Press the POWER switch of the main unit to turn it on.
No sound
e
Check amplifier and digital device connections.
Input indicator flashes.
e
Turn the device connected to the selected input terminal on.
e
Check whether the connection to the selected input
terminal is correct.
A beeping noise occurs at regular intervals.
e
The D-03 is in Word sync mode, but the connected device is
not. Check the connection to the Word sync terminal and
the setup of the connected device.
This phenomenon occurs when the error detected is below
the limit of detection for the D-03 word error that would
normally produce a WRD ERROR.
The WORD indicator flashes.
e
The Word sync mode is selected, but there is no clock
source. Turn the Word sync mode off.
e
An incompatible signal is input. Check Word sync
connections and the setup of the connected devices.
The display shows “NO WORD!”
e
No word clock is being received. Check connections to the
external master clock generator, its power supply and
output status.
e
The Word sync mode is selected, but there is no clock
source. Turn the Word sync mode off.
The display shows “WRD ERROR!”.
e
An incompatible signal is input. Check Word sync
connections and the settings made on connected devices.
e
When a device without a Word sync function is used, use
the WORD button on the unit to turn off the Word sync
function.
The display shows “WRD UNLOCK!”.
e
Connect a clock generator whose output frequency
precision is within ±5 ppm.
If normal operation cannot be obtained, unplug the power
cord from the outlet and plug it again. This resets the
internal micro-computer which can be disturbed during
electrical storms, power interruptions, et cetera.
Troubleshooting Specifications
General
Power supply
Europe model . . . . . . . . . . . . . . . . . . . . . AC 230 V, 50 Hz
U.S.A./Canada model. . . . . . . . . . . . . . . . AC 120 V, 60 Hz
Korea model . . . . . . . . . . . . . . . . . . . . . . AC 220 V, 60 Hz
Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 W
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 kg (59 1/2 lbs)
External dimensions (W x H x D) . . . . . . . 445 x 108 x 420 mm
(17 1/2” x 4 1/4” x 16 9/16”)
Digital Input Terminals
Input format . . . . DSD, linear PCM (32kHz-192kHz, 16-24bit)
i.LINK (AUDIO) terminal (6pin) x2
XLR x 2, Input level: more than 5.0Vp-p/110Ω
(Use 2 terminals for ES-LINK or Dual AES output)
RCA x2, Input level: more than 0.5Vp-p/75Ω
OPTICAL x1, Input level: –24.0 to –14.5dBm peak
Audio features
Analog output level . . . . . . . . . . RCA: 2.2 Vrms/10kΩ (1 kHz)
XLR: 4.4 Vrms/10kΩ (1 kHz)
Frequency response . . . . . . . . . . . . . . . . 2 Hz - 70 kHz, ±3 dB
2 Hz - 25 kHz, ±0.5 dB
Signal-to-Noise Ratio (S/N) . . . . . . . . . . . . . . . . 115 dB (JEITA)
Total harmonic distortion . . . . . . . . . . . . . . . 0.0006% (JEITA)
Word Clock Frequency (input/output)
Jack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BNC
Input or output level . . . . . . . . . . . . . . . . . . . . . TTL level/75Ω
Word Clock Frequency
44.1, 88.2, 176.4, 48, 96, 192, 100 (kHz)
Output precision . . . . . . . . . . . . ±0.5 ppm (in mint condition)
Input frequency range . . . . . . . . . . . . . . . . . . . . . . . . ±5 ppm
Accessories
Power cord x 1
Felt pads x 4
Warranty card x 1
Owner
’
s manual x 1
• Design and specifications are subject to change without
notice.
• Weight and dimensions are approximate.
• Illustrations may differ slightly from production models.