Meridian Audio DVP1500 DVD Player User Manual


 
SETUP
5
SETUP MENU FUNCTIONS
Set: SCANRATE
Select the required scanrate by using the right and
left arrows. When the desired rate is displayed on the
LCD display, press the STORE key on the remote or
ENTER on the front panel. The DVP1000 will ask you
"Are you sure" and press the STORE/ENTER key
again. The scanrate is now selected.
Set: Active Output
Analog/Digital (Default)
This must be selected to determine if the Analog
(BNC) or Digital (DVI) output is used. Both outputs
cannot be used at the same time.
Set: Screen Shape
Wide Screen / 4:3 / Wide 4:3
Note: This sets the processor for the screen shape of
the display to be used. If this is not set properly, the
aspect ratio selection for the different sources
located in the user menu will be incorrect.
•Wide Screen-Choose this when the screen is
Widescreen and the projector will provide the
anamorphic vertical squeeze.
Example: A 16:9 plasma, a digital or CRT projector
set to Anamorphic using a wide angle screen or when
using a Panamorph lens, or a 1280x720 digital
projector.
•4:3– Choose this when the projector is 4:3
and the screen is 4:3
Example: using a 1024x768 digital projector on a 4:3
screen.
•Wide 4:3-Choose this when the digital
projector operates as 4:3 and the screen is
Widescreen. (Not available on units scanning
at rates below 720p)
Example: A digital projector that has a 4:3 display
chip that locks the aspect ratio when sent the native
resolution and then displayed on a wide angle screen.
Output Format (Analog)
RGB (Default) /YPrPb
Note: Selecting RGB means connecting the
processor to the display via five wire analog RGBHV.
This function is not active when DVI output is
selected. DVI is always RGBHV.
Composite Sync on H
On/Off (Default)
Note: this function is not active when YPrPb
output is selected.
Horizontal Sync Polarity
Negative (Default) / Positive
Changes sync polarity, which may be needed for
compatibility with some displays.
Vertical Sync Polarity
Negative (Default) / Positive
Changes sync polarity, which may be needed for
compatibility with some displays
Note: Each input on the DVP1500 can be activated
or deactivated to simplify operation so unused inputs
are not accessed when cycling through the inputs
with the remote control.
Set: Video Input
Enabled (Default) /Disabled
Note: Disabling this unused input will remove it from
the input menu list.
Set: S-Video Input
Enabled (Default) /Disabled
Note: Disabling this unused input will remove it from
the input menu list.
Set: RGB Input
Enabled (Default) /Disabled
Note: Disabling this unused input will remove it from
the input menu list.
Set: YCrCb Input
Enabled (Default) /Disabled
Note: Disabling this unused input will remove it from
the input menu list.
Set: DVI Input
Enable / Disable
Note: Disabling this unused input will remove it from
the input menu list.
Set: Passthru Input
Enabled (Default) /Disabled
Note: Disabling this unused input will remove it from
the input menu list.
Set: Passthru Transcode
Disable (Default) /Enable
YPrPb HDTV signals via the D15 input or the YPrPb
(BNC) inputs can be transcoded to RGB when this
feature is enabled.
Set: Component Input Standard
DVD (Default) /Professional (Betacam)
Note: Only use professional setting when using
a device that conforms to SMTPE Betacam levels
Set: RGB Input Sync
Sync-on-Green (Default) /TTL/Video
OSD (On Screen Display)
On (Default) /Off