Filter
Top Products
E-41
English
FACTORY SETTINGS
This display can store parameter settings for eight additional signals for both RGB1 and RGB2.
To do this, select a desired signal and follow the instructions in “Adjusting Screen Position and Size” on P. E-28–E-29 to adjust the
parameters. When you finish, the settings will be automatically stored. Thus, when the display receives that signal, images will be
displayed in accordance with the settings you most recently selected.
This display has been factory-set for 18 different signals as shown below.
Factory-set signals (RGB1, RGB2 modes)
• The dedicated graphics card is optionally available.
• With the 800 x 600 and 1024 x 768 modes, images of reduced size are displayed on the screen, using size reduction and interpolation. Note also
that on-screen information is also displayed in reduced size.
•“Out of range” appears if the display receives a signal whose characteristic does not fall within the display’s permissible range.
• You can check input signals through “Status” on the OTHERS Menu screen. (See P. E-32–E-34.)
• All terms (i.e., company and product names) used in this document are trademarks or registered trademarks.
Factory-set signals (Comp.video mode)
852 x 480 31.72 59.97 When a dedicated graphics card is used
640 x 480 31.47 59.94 VGA
640 x 480 37.86 72.81 VGA 72 Hz
640 x 480 37.50 75.00 VGA 75 Hz
640 x 480 43.27 85.01 VGA 85 Hz
720 x 400 31.47 70.09 VGA 400 lines
640 x 400 37.86 85.08 VGA 400 lines
800 x 600 35.16 56.25 SVGA 56 Hz
640 x 400 37.88 60.32 SVGA 60 Hz
800 x 600 48.08 72.19 SVGA 72 Hz
800 x 600 48.88 75.00 SVGA 75 Hz
1024 x 768 48.36 60.00 XGA 60 Hz
640 x 480 35.00 66.67 MAC 13RGB
848 x 480 31.02 60.00
640 x 480 15.73 59.94 60 fields
640 x 480 15.63 50.00 50 fields
640 x 400 24.82 56.42 NEC 24 kHz
640 x 400 31.50 70.15 NEC 31 kHz
15.63 to 80.00* 50.00 to 120.00* User setting
Signal
Display (dots x lines)
Horizontal frequency (kHz) Vertical frequency (Hz)
15.73 59.94 SDTV 525i
15.63 50.00 SDTV 625i
31.47 59.94 SDTV 480p
45.00 60.00 HDTV 720p
44.96 59.94 HDTV 720p
33.75 60.00 HDTV 1080i
33.72 59.94 HDTV 1080i
Horizontal
frequency (kHz)
Signal
Vertical
frequency (Hz)
Factory-set signals (Video, S-video mode)
15.73 59.94 NTSC
15.63 50.00 PAL
15.63 50.00 SECAM
15.73 59.97 4.43NTSC
15.73 59.97 M-PAL
15.63 50.00 N-PAL
Horizontal
frequency (kHz)
Signal
Vertical
frequency (Hz)
* With some input signals, “Out of range” may appear even when the horizontal and vertical frequencies are within their permissible ranges. Make
sure that the vertical frequency of the input signal is 75 Hz or less for SVGA and 60 Hz for XGA.
In the Comp.video and Video/S-video modes, the display has been factory-set as follows for different input signals: