Filter
Top Products
HOW TO USE THE REMOTE TO CONTROL YOUR TV
(_CD, AMP buttons
When pressed, each of these buttons will blink to indicate the remote is in Audio mode (see page 39).
(_) CHANNEL selector buttons
CHANNEL selector buttons are used to select channels, lock access code, etc.
Enter one, two, or three numbers to select channels. Enter "0" first for channels 1 to 9, or simply press the single digit channel you
wish to tune then wait a few seconds for the TV to tune. For channels 100 and above, press the "1" button, wait until two dashes
appear next to the channel display on your TV, then enter the remaining two numbers using the number buttons.
Channel selection may also be performed by pressing CH up (A) or down (•).
When inANT C, digital channels are indicated by the use of a (_) DASH in the subchannel number (for example "15-1"). Press
buttons [0], [1], [5], [1] to tune to subchannel 15-1 or buttons [0], [1], [5], [0], [0], [1].
I NOTE: The TV may not receive some channels if you are not in the correct ANTENNA/CABLE mode (see page 51).
(_) SLEEP and (-) DASH button
Press this button to display the sleep timer in the lower left corner of the screen. Every subsequent press of this button will add 15
minutes to this timer, up to a maximum of three hours. Once set, use INFO when you want to view time remaining. If the SLEEP
button is pressed while the timer is set, it will reset to the original condition.
When in ANT C, Digital channels are indicated by the use of a (-) DASH in the subchannel number (for example "15-1"). Press
buttons [1], [5], [-], [1] to tune to subchannel 15-1.
(_) INFO button
Press this button when you want to check the channel being received, the picture source, if the channel has stereo (ST) or second
audio program (SAP), the time, CHANNEL ID and if the TIMER is set.
Day/N
Closed Moc
Captioning --
ANT A/ANT B
3:32 PM
Ant A 22
Stereo
R
1080i Format
-_ QOff Q,,0:00 AM
t
Off Timer
Virtual HD
Mode
_pTimer
an S-VIDEO
Input is connected to
VIDEO: 3.
a
COMPONENT
VIDEO: Y-PBPR Input
is connected to
VIDEO: 1.
iii_|||i|i|i|i|i|i|i|i|i|!i|
iii i !i ii:i:i:i:i:i:i:i:iiii
iii (i,] ii!iiii!i!i!i!i!i!;!
iiiO|i i|i|i|i|ii|i|i|i|!ii¸
iiim|||||||i|i|i|i|i|i|i
iiiZ||;|;|;|;|;|;|;|;|i||
iii_|||||||||!;i_ii_
h
ANT C
blain Picture
Source
IEEE1394
When an IEEE1394 device
Esconnected
Program Name --
and Information
Day/N
Closed Mo(
Captioning --
_ho's Who _tL t_he ZOO KpBS,,DT
_ht
_-_" @]Day rBe 4:3Expanded E_1080i|-_ I©off _,, 0_00 Abl t_ _l--
Wide Mode Off Timer Virtual HD
TV Time
• Channel ID
• Program Time
• Digital Closed Caption
• Broadcast Raling
• Program Language
• Digital Inp{_t Signal
-- S_eep Timer
"Multi
Channel
Programs
NOTES: 1. When an IEEE1394 device is connected, press CH A, CH • buttons to change Multi Channel programs.
2. When in ANT C or a 1394 device, press the INFO button twice (2x) to see detailed program information when
available.
23