Filter
Top Products
26
HOW TO USE THE REMOTE TO CONTROL YOUR TV
ቨ CD, TAPE, AMP buttons
When pressed, each of these buttons will blink to indicate the remote is in Audio mode (see pages 40 and 41).
ቩ CHANNEL selector buttons
CHANNEL selector buttons are used to select channels, lock access code, etc.
Enter one, two, or three numbers to select channels. Enter “0” first for channels 1 to 9, or simply press the single digit channel you
wish to tune then wait a few seconds for the TV to tune. For channels 100 and above, press the “1” button, wait until two dashes
appear next to the channel display on your TV, then enter the remaining two numbers using the number buttons.
Channel selection may also be performed by pressing CH up (̆) or down (̄).
When in ANT C, digital channels are indicated by the use of a (-) DASH in the subchannel number (for example “15-1”). Press
buttons [0], [1], [5], [1] to tune to subchannel 15-1 or buttons [0], [1], [5], [0], [0], [1].
ቪ SLEEP and (-) DASH button
Press this button to display the sleep timer in the lower left corner of the screen. Every subsequent press of this button will add 15
minutes to this timer, up to a maximum of three hours. Once set, use INFO when you want to view time remaining. If the SLEEP
button is pressed while the timer is set, it will reset to the original condition.
When in ANT C, Digital channels are indicated by the use of a (-) DASH in the subchannel number (for example “15-1”). Press
buttons [1], [5], [-], [1] to tune to subchannel 15-1.
ቫ INFO button
Press this button when you want to check the channel being received, the picture source, if the channel has stereo (ST) or second
audio program (SAP), the time, CHANNEL ID and if the TIMER is set.
NOTE: The TV may not receive some channels if you are not in the correct ANTENNA/CABLE mode (see page 63).
Stereo (480i)
ST/SA
Audio
Broadcast
Audio Selected
Main Picture Source
Channel ID/Video ID
Time
PIP/Sub-Picture
Source
Signal Format
Received
TV-PG DLSV
PIP TV-PG DLSV
Broadcast
Rating
16:9 Standard
1080i
Movies
C.C. On
Off 10:05 AM
Time Lock 10:05 AM
Wide
Mode
Virtual
HD
Picture
Mode
Closed
Captioning
Off Timer
TV Time Lock
Ant A 15
ABCDEFG
10:10 AM
PIP Ant A 10
PIP/Sub-Picture
OFF
Main Picture
When an S-VIDEO
Input is connected to
VIDEO: 3.
When a COMPONENT
VIDEO: Y-P
B
P
R
Input
is connected to
VIDEO: 1.
S - IN: 3
YPBPR:1
ANT A/ANT B
Barney & Friends Ant C 15-2
Who’s Who at the Zoo KPBS-DT
Barney and the chi...4:00PM 5:00PM
TV-PG Engl CC 5.1ch
9:14AM
4:3 Standard
1080i
Sports
C.C. On
480i
Closed Captioning
Picture Mode
Virtual HD
Wide Mode
Program Name
and Information
Digital Input Signal
TV Time
Main Picture
Source
Channel ID
Program Time
Audio Channel
Digital Closed Caption
Program Language
Broadcast Rating
No Information IEEE1394 01/04
PBS 1 DT
-:--AM -:--AM
Multi CC 5.1ch
9:14AM
16:9 Standard
1080i
Sports
C.C. On
1080i
When an IEEE1394 device
is connected
Multi
Channel
Programs
ANT C
IEEE1394
NOTE: When an IEEE1394 device is connected, press CH ̆, CH ̄ buttons to change Multi Channel programs.
THE REMOTE CONTROL