Filter
Top Products
87
Controlling Other Components
—Continued
The DPS-10.5’s remote controller can learn individual
commands from other component’s remote controllers
and then be used to control those components. Com-
mands can be learnt by the dedicated leaning buttons—
[L1], [L2], [L3], and [L4]—or any button. Each button
can learn up to four commands, one for each remote con-
troller mode: DVD, Amp, VCR, and TV.
If you’ve entered a control code for a component
(page 82) and certain buttons don’t work as expected,
you can also use this function to program those buttons
individually.
Notes:
• The following buttons cannot learn new commands:
[LIGHT] and the [DVD], [Amp], [VCR], and [TV]
Mode buttons.
• Learning mode is cancelled automatically if you don’t
press any buttons for 30 seconds.
• The DPS-10.5’s remote controller comes prepro-
grammed with the commands necessary for control-
ling Integra DVD players (DVD mode) and AV
receivers (Amp mode). However, you can reprogram
individual buttons if necessary. The original com-
mands can be restored by resetting the remote
controller.
•To program a button that has already learnt a com-
mand, repeat this procedure. The previously learnt
command will be overwritten.
• Like most remote controllers, the DPS-10.5’s remote
controller uses infrared. Commands from remote con-
trollers that don’t use infrared cannot be learnt.
• When the remote controller’s batteries expire, all
learnt commands may be lost and will have to be learnt
all over again, so keep your other remote controllers in
a safe place.
Learning the Commands of Other
Remote Controllers
1
Point the remote controllers at each other,
about 2 to 6 inches (5–15 cm) apart.
2
While holding down the [DVD], [Amp],
[VCR], or [TV] Mode button, press the [On]
button, and then release both buttons.
The Mode button and Tx/Learn indicator light up.
+
10 0
Clear
123
456
789
Input
I
+
-
Enter
S
e
t
u
p
R
e
t
u
r
n
L4
L2L1
V OffV In
Aspect
A
-
B
Repeat
Rsltn
Angle
Subtitle
Audio
L3
T
o
p
M
e
n
u
M
e
n
u
VOL
+
-
V3
TV
InputDMS
DVD Amp VCR
DVD
V1 V2
LM RD
Zoom
CH
L Mode
Learning
Search Memory Dimmer
Amp Input
Display
Audio
Sel
Zoom
On
Picture Control
Random
Step/Slow
Muting
AngleSubtitleAudio
AspectA
-
BRepeat
On Standby
T
V
T
V CH
T
V VOL
RC
-
562DV
Last Memory
Resolution
Mode
Amp Input
Rec
Open
/
Close
Video Input Video Off
On
Mode
P
O
W
E
R
S
L
E
E
P
D
I
M
M
E
R
S
U
R
M
O
D
E
V
I
D
E
O
-
1
V
ID
E
O
-
2
T
A
P
E
D
V
D
C
D
C
D
D
V
D
T
U
N
E
R
T
U
N
E
R
P
H
O
N
O
IN
P
U
T
S
E
L
E
C
T
O
R
D
IS
C
T
A
P
E
V
O
L
U
M
E
L
E
V
E
L
C
H
S
E
L
P
R
E
S
E
T
M
U
T
I
N
G
T
E
S
T
T
O
N
E
M
U
L
T
I-
C
H
IN
P
U
T
R
E
M
O
T
E
C
O
N
T
R
O
L
LE
R
G
R
O
U
P
R
C
-3
8
5
S
2–6" (5–15 cm)
RC-563DV
3
On the DPS-10.5’s remote controller, press
the button that you want to learn the new
command.
The Tx/Learn indicator goes off while the button
is being pressed, and comes back on again when
it’s released.
Use the dedicated leaning buttons—[L1], [L2],
[L3], and [L4]—or another button.
4
On the other remote controller, press and
hold the button whose command you want
to learn until the Tx/Learn indicator
flashes.
If the command is learnt successfully, the Tx/
Learn indicator flashes slowly twice, and then the
Mode button and Tx/Learn indicator remain lit.
If the Tx/Learn indicator flashes quickly three
times, the command has not been learnt, in which
case you should try again from step 3.
If the Tx/Learn indicator flashes quickly six times,
the remote controller’s memory is full and no
more commands can be learnt.
5
To learn more new commands, repeat
steps 3 and 4.
When you’ve finished, press the Mode button that
you pressed in step 2.
To use the learnt command, select the relevant
mode, and then press the button.