Filter
Top Products
Filename [XV38ASAG_057S-VHS.fm]
Masterpage:Left+
32 EN
Page 32 December 8, 2004 3:22 pm
OPERATIONS ON VHS DECK (cont.)
Automatic Satellite
Programme Recording
This function allows you to automatically record a
satellite programme which is timer-programmed on your
external satellite receiver. Connect a satellite receiver to
the unit’s L-1 Input Connector (INPUT (L-1)) and
programme the timer on the satellite receiver. The unit
starts or stops recording by the signals input from the
satellite receiver. After recording, the unit’s power shuts
off automatically.
A
Select the VHS deck.
On the unit
Press VCR/DVD repeatedly so that the VCR indicator
lights up.
On the remote control
Press VCR so that the VCR indicator lights up.
B
Set the tape speed.
Press p.
C
Engage the Automatic Satellite Programme
Recording mode.
Press and hold REC LINK for
about 2 seconds.
● The “N” and “#” indicators light
up and the unit turns off
automatically.
NOTES:
● Operation on the DVD deck is not possible when the
Automatic Satellite Program Recording mode is engaged, or
Timer Recording is in progress.
● To disengage the Automatic Satellite Programme Recording
mode, press REC LINK. The “N” indicator goes off.
● If the unit’s power is off, it is not possible to engage the
Automatic Satellite Programme Recording mode.
● In step C, if the “N” indicator does not light but instead blinks
quickly even though your satellite receiver’s power is off,
Automatic Satellite Programme Recording will not work
properly with that satellite receiver*.
* Some satellite receivers output signals even if the power is off.
Automatic Satellite Programme Recording is not possible with those
satellite receivers.
● The “N” indicator blinks while Automatic Satellite Programme
Recording is in progress.
● For timer programming of the satellite receiver, refer to the
instruction manual of the satellite receiver.
● Automatic Satellite Programme Recording is not possible if
your satellite receiver does not have a timer.
● Pressing the unit’s 1 button while Automatic Satellite
Programme Recording is in progress turns off the unit’s power
and disengages the Automatic Satellite Programme Recording
mode.
● If there are more than one satellite programmes you wish to
record with Automatic Satellite Programme Recording, it is not
possible to set different tape speeds for each programme.
● Depending on the type of satellite receiver, the unit may not
record a slight portion of the beginning of the programme or
may record slightly longer than the actual length of the
programme.
● If you engage the Automatic Satellite Programme Recording
mode when the satellite receiver’s power is on, the unit will
not start Automatic Satellite Programme Recording even
though the “N” and “#” indicators blink. When the satellite
receiver shuts off once and is turned back on again, the unit
starts recording.
● You can also record a programme from your cable system in
the same way if the system has a timer.
● The B.E.S.T. system (
੬ pg. 25) does not work while Automatic
Satellite Programme Recording is in progress.
ATTENTION
● Be sure not to turn on the satellite receiver before the
programme is executed; otherwise, the unit will start
recording when the satellite receiver’s power is turned on.
● If you have connected another appliance other than a
satellite receiver to the
L-1 Input Connector (INPUT
(L-1)), be sure not to engage the Automatic Satellite
Programme Recording mode; otherwise, the unit will start
recording when the connected appliance’s power is turned
on.
● Automatic Satellite Programme Recording and timer-
recording cannot be done at the same time.
Before performing the following steps:
● Make sure the satellite receiver is connected to the unit’s
L-1 Input Connector (INPUT (L-1)) connector.
● Programme the timer on the satellite receiver.
● Insert a cassette with the safety tab in place.
● Slide the TV/VCR/DVD switch on the remote control to the
right.
Slide to the
right.
XV38ASAG_EN_BOOK.book Page 32 Wednesday, December 8, 2004 4:00 PM