JVC SR-MV55U DVD VCR Combo User Manual


 
Masterpage:Right+
EN 51
Filename [SR-MV45_55U_10Editing.fm]
Page 51 January 10, 2007 1:18 pm
EDITING
You can dub programs from a DV camcorder or DV equipment
connected to the unit with a DV cable. The unit’s remote control
allows you the limited control of the connected DV camcorder or
DV equipment functions during dubbing.
1 Connect a DV camcorder or DV equipment to the [DV IN]
connector on the unit’s front panel.
2 Load a DVD-RAM/RW/R disc on the unit.
3 Press VCR/DVD repeatedly so that the DVD lamp lights up on
the unit.
4 Press INPUT SELECT +/– on the unit or INPUT +/– on the
remote control to set the input to “DV”.
The “DV DUBBING” controller appears on the TV screen.
If “ ” does not appear on the “DV DUBBING” controller, make
sure the DV equipment is connected correctly.
5 Press REC MODE repeatedly to set the recording mode.
(pg. 36)
6 Locate the point from where you want to start dubbing, then
stop or pause playback by pressing the following buttons on the
remote control: 4, 5, 3, 8, 9
To play back in slow speed (1/10 of the normal speed), press 9 to
pause playback, then press 3 or 5.
To play back frame-by-frame, press 9 to pause playback, then press
9 repeatedly. Each press of 9 advances a frame.
To change the playback direction, press 3 or 5.
7 Press we to select , then press ENTER.
8 Press rt to select the desired
sound track, then press ENTER.
AUDIO 1: Select this to record the
original stereo sound played
back on the connected DV
equipment.
AUDIO 2: Select this to record the
dubbed stereo sound played
back on the connected DV
equipment.
MIX: Select this to record the sound of both “AUDIO 1” and
“AUDIO 2”.
Note that this selection is not available when the source program is
recorded in 16BIT (48 kHz) mode.
9 Press we to select , then press ENTER. The
dubbing starts.
Playback on the external DV equipment and recording on the unit
should start simultaneously.
When the playback from the beginning is not possible, the “DV
DUBBING” controller cannot be used. Perform dubbing without using
the “DV DUBBING” controller. (below)
To pause dubbing, press we to select , then press
ENTER. Both the unit and the external DV equipment pause dubbing.
Pressing 9 on the unit also works the same way.
To clear the “DV DUBBING” controller from the TV screen, press ON
SCREEN.
10 Press 8 on the remote control to stop dubbing.
Both the unit and the external DV equipment stop dubbing.
NOTES:
Dubbing copyright guarded programs is not possible.
Original DV information such as the recording date and time are not
recorded.
The superimposed indication during the operation or dubbing is not
recorded.
It is not possible to perform dubbing when
the dubbing (DUBB.)
lamp
lights up on the unit. Press VCR]DVD so that the dubbing
(
DUBB.) lamp lights off.
Performing dubbing without using the “DV DUBBING”
controller
A Press INPUT SELECT +/– on the unit or INPUT +/– on the
remote control to set the input to “DV”.
B Press REC MODE repeatedly to set the recording mode.
(pg. 36)
C Start playback on the external DV equipment slightly before the
actual point from where you wish to start dubbing.
D Press 7 on the unit to start recording. Or while holding 7, press
4 on the remote control. The dubbing starts.
E When the dubbing ends, press 8 on the unit, then stop
playback on the external DV equipment.
DV Dubbing (DVD Deck Only)
NOTES:
Use the DV cable VC-VDV 204U for connection.
When you connect a PC to the [DV IN] connector, we do not
assure the normal operation of this unit.
To [DV IN]
DV cable
(VC-VDV 204U)
(not supplied)
DV Camcorder
DV connector
Your unit
DV equipment
SR-MV45_55US.book Page 51 Wednesday, January 10, 2007 1:18 PM