Filter
Top Products
42 EN42 EN
TIMER RECORDING
1
Press [TIMER].
2
Use [K / L] to select “New Program”,
then press [OK].
Timer Programming
TUE JAN/01 11:00AM
Date Start End CH
New Program
• If there are 6 or more programs, use
[H / G] to change pages.
3
Use [K / L] to enter the date, then
press [B].
Date
JAN/02
REC To Mode
DVD SP
SP 2h00m
Start
- - : - -
End
- - : - -
CH
DTV125. 1
Daily
MON-SAT
JAN/01
JAN/31
MON-FRI
SAT
FRI
SUN
p
p
p
p
p
p
p
p
You can program the unit to record up to 12 programs
within a month in advance. Daily or weekly program
recordings are also available.
Before recording, make sure
• Set the clock before setting a timer programming.
• Insert a recordable disc with enough recordable space.
Guide to Timer Programming Display
Timer Programming
1/1
TUE JAN/01 11:00AMSP (1:00)
JAN/ 2/08 12:00 AM 125.1 SP
Date Start End CH
JAN/02 12:00AM 1:00AM DTV125. 1
New Program
1
5
3
4
2
6
1 Title of a timer program (Contains date, time, channel,
recording mode of the program)
2 Current date and time
3 Recording mode, and length of the recording
4 Timer program list
5 Total number of pages and current page (2 pages
maximum)
6 Recording media (“
” (DVD) or “ ” (VCR))
When pressing [L] at
the current date, the
date will change as
follows.
e.g.) January 1st
Note
• If you have not set the clock yet:
Entry screen for the clock setting will appear instead
of the timer programming list at step 1. Continue
with the step 4 in “Manual Clock Setting” on page 31
before setting a timer programming.
• Use [s / B] to move the cursor to the left and the
right in the entry screen for the timer programming.
• If a basic recording or one-touch timer recording is in
progress on one component (e.g., VCR) and the timer
recording set for the other component (e.g., DVD) is
about to begin, the unit automatically switches to the
programmed channel for timer recording 2 minutes
before the programmed starting time, and the
recording in progress (for VCR) will be canceled
UNLESS their recording channels are the same. If their
recording channels are the same, the timer recording
will start without canceling the recording currently in
progress. In this case, the recording of the same
channel will be made on both DVD and VCR.
• You cannot make a program whose recording time
exceeds 12 hours.
• Cancel the timer-standby mode by pressing
[TIMER SET] before operation for either DVD or VCR.
When finished operating, press [TIMER SET] to
resume the timer-standby mode.
• In the timer-standby mode, you can turn on the
power and use the component (VCR or DVD) which is
not currently timer-programmed.
DTV/TV
ABC DEF.@/:
JKL MNOGHI
TUV WXYZ
SPACE CLEAR
SETUPDISC MENU
RETURNTITLE
CHANNEL
TIMERREC MODE
AUDIOREC HDMI
PQRS
SOURCE
123
456
78
.
0
OK
+--
o
p
B
B
iji
C
F
gh
s
9
DISPLAY OPEN/CLOSE
I
A
VCR DVD
RAPID PLAY
CM SKIP
D.DUBBING TIMER SET
ABC DEF.@/:
JKL MNOGHI
TUV WXYZ
SPACE
PQRS
123
456
78
0
9
SETUP
p
o
OK
B
s
TIMER SET
TIMER
.
iij
E9M81UD_ZV457MG9.indd 42 2008/05/15 14:31:11