Filter
Top Products
Press this key on the remote
control....
The screen displays Explanation
4. Store the setting and return
to TV picture
TV picture
Prog Logo Channel Signal
▲▼
>> weitere Einstellungen
Std., Pict., Sound
698-03A-GB
VTR1
ARD
ZDF
SAT 1
00
06
34
40
Video Rec.1
Aerial
Aerial
Aerial
0
1
2
3
4
5
6
7
8
9
Station table
Std channel 06 ARD
Spec. channel
SAT-TV
SAT-RADIO
Fine tuning
?
MENU
return Help
TV
picture
red
yellow
blue
Prog Logo Channel Signal
▲▼
>> weitere Einstellungen
Std., Pict., Sound
698-03A-GB
VTR1
ARD
ZDF
SAT 1
00
06
34
40
Video Rec.1
Aerial
Aerial
Aerial
0
1
2
3
4
5
6
7
8
9
Station table
Std channel 06 ARD
Spec. channel
SAT-TV
SAT-RADIO
Fine tuning
?
MENU
return Help
TV
picture
red
yellow
blue
Prog Logo Channel Signal
▲▼
>> weitere Einstellungen
Std., Pict., Sound
698-03A-ST-GB
VTR1
ARD
ZDF
SAT 1
00
06
34
40
Video Rec.1
Aerial
Aerial
Aerial
0
1
2
3
4
5
6
7
8
9
Station table
Std channel 06 ARD
Spec. channel
SAT-TV
SAT-RADIO
Fine tuning
?
MENU
return Help
TV
picture
red
yellow
blue
store?
OK
8
OK
TV
3. Presetting TV stations
Direct channel entry/
station search
The TV is supplied with factory preprogrammed TV stations. However, if you can receive TV stations in your area that are not listed in the
station table, then these transmitters can be entered and programmed at any time.
You can choose one of the following three programming possibilities:
a) Direct channel entry b) Station search c) Autostore function
1. Call the station table and
channel type survey
2. Select the type of channel
(e.g. standard channel)
3. Enter the channel number
(Example: Standard channel
06) or start station search
With direct channel entry it is necessary to know the
type of channel and the channel number.
If type and number of channel are not known, you can
scan through the entire reception range with the
search function to locate stations.
The station table lists all the preset stations.
These stations can be changed at any time.
The cursor always highlights the type of channel cur-
rently preset in the given programme position.
For the search function it is advisable to switch to a
vacant programme position.
The yellow framed field offers four types of channels.
Select the channel type with the assigned coloured
key.
After the channel type has been selected, a channel
number is displayed in the bar when a station is stored
in this programme position. Two lines are shown if this
position is still vacant.
„SAT channel“ and „SAT radio channel“ can only be
selected if a SAT upgrade module has been installed in
the TV receiver.
6
0
+
-
or
yellow
blue
With direct channel entry, the station table is briefly
faded out when the channel number is entered, and
the selected station is displayed.
The station search proceeds from the displayed
channel number in a forward sequence with the
key, and in a reverse sequence with the key.
Search proceeds from the lower channel area
upwards or downwards when two lines are displayed.
The search stops when a station has been found.
Proceed as described in step 4 if the located station is
to be stored.
Press the or key if the located station is not to be
stored so that the search can be continued.
Complete fine tuning if station reception is not clear
(see Section 3.2).
-
+
-
+