Mitsubishi Electronics WS-65615A Projection Television User Manual


 
10
11
SERVICEWARNING
X-RAYPRECAUTION:
THISPRODUCT
INCLUDES CRITICAL MECHANICAL
AND ELECTRICAL PARTS WHICH ARE
ESSENTIAL FOR X-RADIATION SAFETY.
FOR CONTINUED SAFETY REPLACE
CRITICAL COMPONENTS INDICATED
IN THE SERVICE MANUAL ONLY WITH
EXACT REPLACEMENT PARTS GIVEN
IN THE PARTS LIST. REFER TO SERVICE
MANUALFOR OPERATING HIGH VOLTAGE AT
MINIMUM BRIGHTNESS, MEASUREMENT
PROCEDURES AND PROPER SERVICE
ADJUSTMENTS.
WARNING:
HANDLEWITHCARE. HIGH
VACUUM PICTURE TUBE IS DANGEROUS
TO HANDLE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
REPLACE WITH A TUBE OF THE SAME
TYPE NUMBER FOR CONTINUED SAFETY.
CAUTION:
TO MEASURE SECOND
ANODE VOLTAGE USE A HIGH VOLTAGE
METERCONNECTEDFROMANODELEAD
TO CHASSIS ONLY. DISCHARGE HIGH
VOLTAGE TO CHASSIS ONLY, NOT TO
EXTERNALGROUND.
IREMITTER
NetCommand
R
DIGITAL
SERVICE
PORT
IEEE1394
INPUT/OUTPUT
AUDIO
ANT-2
AUX
ANT-1
MAIN
CableCARD
TM
SLOT
(DTV/CABLE /VHF/UHF)
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
INPUT MONITOR OUTPUT
AUDIO 2
AUDIO/VIDEO 1
1 2
COMPONENT
YPbPr (480i/480p/1080i)
21
Y
Pb
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
DVI
DigitalVideo
DigitalAudio
AnalogAudio
11.
1.
2. 3.
4.
5.
6.
7.
8.
9.
10.
Back Panel
1. IEEE-1394 Input/Output
Use these jacks to connect the TV to external IEEE
1394 digital products by means of a single cable. There
are two jacks on the back panel for all models. For
WS-55615, WS-55615A, WS-65615, WS-65615A and
WS-73615 there is an additional jack on the front
panel. IEEE 1394 connections provide a high degree
of flexibility when connecting your NetCommand®
controlled system. Detailed information regarding IEEE
1394 connection requirements are in Chapter 4.
2. Antenna (ANT-1 MAIN, ANT-2 AUX)
ANT-1 MAIN and ANT-2 AUX can each receive both
digital/analog over-the-air channels from a VHF/UHF
antenna or non-scrambled digital/analog cable
channels.
Your primary viewing signal source should be
connected to ANT-1 MAIN. ANT-1 MAIN must be
used to view premium subscription cable TV service
authorized by the CableCARD™ access card. The
CableCARD access card is provided by your local
cable company. ANT-2 AUX can continue to receive
over-the-air or non-scrambled cable signals.
3. Digital Audio Output
This output will automatically send Dolby® Digital audio
from digital channels, IEEE 1394 devices and HDMI™
(not DVI) signals to a digital Audio/Video receiver.
Connect this output to the A/V receiver’s coaxial digital
audio input. This output will automatically turn off when
viewing an analog channel or device. Use Monitor
Ouput Audio 2 to send analog signals to your A/V
receiver.
Some digital cable channels send MPEG-1 digital audio
instead of Dolby Digital, however, not all A/V receivers
can decode MPEG-1 digital audio. This can cause the
A/V receivers to produce a loud noise that can damage
speakers. For this reason, the TV will automatically
turn off the digital audio output when tuned to a
channel or device that has MPEG-1 digital audio and
send it to the A/V receiver as analog left and right audio
from Monitor Output. You can enable the digital output
to include MPEG-1 digital audio if your A/V receiver
is capable of decoding it. See Edit NetCommand for
details.
4. CableCARD™ Slot
The CableCARD access card provided by your cable TV
service provider is inserted into this slot. CableCARD