Mitsubishi Electronics WS-65615A Projection Television User Manual


 
20
21
Connecting an HDMI Device or
External DTV Receiver with Component Video
See Appendix B for component video signal
compatibility information.
For digital audio connections, see your DTV
Receiver and A/V Receiver Owner’s Guides.
IMPORTANT
DTVReceiver(withYPrPbconnections)
V
I
D
E
O
Y
P
r
P
b
S
-
V
I
D
E
O
V
C
R
C
O
N
T
R
O
L
P
H
O
N
E
J
A
C
K
R
F
R
E
M
O
T
E
O
U
T
T
O
T
V
C
H
3
C
H
4
C
A
U
T
I
O
N
R
I
S
K
O
F
E
L
E
C
T
R
I
C
A
LS
H
O
C
K
D
O
N
O
T
O
P
E
N
D
I
G
I
T
A
L
A
U
D
I
O
O
U
T
White
Red
Incoming
Antenna
orCable
SATELLITEIN
INFROMANT
or
toantenna,
cableorsatellite
A
U
D
I
O
L
R
A
U
D
I
O
L
R
V
I
D
E
O
SERVICEWARNING
X-RAYPRECAUTION:
THISPRODUCT
INCLUDES CRITICAL MECHANICAL
ANDELECTRICAL PARTS WHICH ARE
ESSENTIAL FOR X-RADIATIONSAFETY.
FOR CONTINUED SAFETY REPLACE
CRITICAL COMPONENTS INDICATED
IN THE SERVICE MANUALONLYWITH
EXACTREPLACEMENT PARTS GIVEN
INTHE PARTSLIST. REFER TOSERVICE
MANUALFOROPERATINGHIGHVOLTAGEAT
MINIMUM BRIGHTNESS,MEASUREMENT
PROCEDURES AND PROPERSERVICE
ADJUSTMENTS.
WARNING:
HANDLEWITHCARE.HIGH
VACUUMPICTURETUBEISDANGEROUS
TO HANDLE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
REPLACE WITHATUBE OFTHE SAME
TYPENUMBERFORCONTINUEDSAFETY.
CAUTION:
TOMEASURE SECOND
ANODEVOLTAGEUSEAHIGHVOLTAGE
METERCONNECTEDFROMANODELEAD
TOCHASSISONLY. DISCHARGE HIGH
VOLTAGE TOCHASSISONLY,NOTTO
EXTERNALGROUND.
IREMITTER
NetCommand
R
DIGITAL
SERVICE
PORT
IEEE1394
INPUT/OUTPUT
AUDIO
ANT-2
AUX
ANT-1
MAIN
CableCARD
TM
SLOT
– (DTV/CABLE /VHF/UHF) –
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
INPUT MONITOR OUTPUT
AUDIO 2
AUDIO/VIDEO 1
1 2
COMPONENT
YPbPr (480i/480p/1080i)
21
Y
Pb
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
DVI
DigitalVideo
DigitalAudio
AnalogAudio
ANT-1
MAIN
– (DTV/CABLE /VHF/UHF) –
Y
Pb
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
COMPONENT
YPbPr (480i/480p/1080i)
21
White
Red
1.
1.
2.
2.
3.
3.
4.
4.
Figure 12. Connecting an External DTV Receiver with
Component Video Connections
External DTV Receiver with
Component Video
Figure 12
A coaxial splitter, RCA video cables and audio cables are
required. These are not included with the TV.
1. Connect the outside antenna, cable or satellite to
ANT or SATELLITE IN on the DTV receiver (see your
DTV receiver’s owner’s guide for instructions and
cable compatibility).
2. Connect the incoming terrestrial antenna or cable
(not satellite) to ANT-1 on the TV back panel
(a coaxial splitter, available at most electronic
supply stores, may be required to complete this
installation).
3. Connect RCA-type cables from the YPrPb outputs
on the DTV receiver to either Component 1 or
2 on the TV back panel, matching the correct
connections:
DTV Receiver to TV Back panel
Y to Y
Pr to Pr
Pb to Pb
4. Connect the L (left) and R (right) audio cables from
the DTV receiver to Component 1 or 2 AUDIO LEFT
and AUDIO RIGHT on the TV back panel. If you
connected the YPrPb outputs to Component 1, also
use Component 1 to connect the audio cable. The
red cable connects to the R (right) channel and the
white cable connects to the L (left) channel.
Note: To utilize the benefits of a digital A/V
receiver, connect your DTV receiver’s digital
audio out to a digital input on your digital A/V
receiver.
SERVICEWARNING
X-RAYPRECAUTION:
THISPRODUCT
INCLUDES CRITICAL MECHANICAL
ANDELECTRICAL PARTS WHICH ARE
ESSENTIAL FOR X-RADIATION SAFETY.
FOR CONTINUEDSAFETY REPLACE
CRITICAL COMPONENTS INDICATED
IN THE SERVICE MANUALONLYWITH
EXACTREPLACEMENT PARTSGIVEN
INTHE PARTSLIST. REFER TOSERVICE
MANUALFOROPERATINGHIGHVOLTAGEAT
MINIMUM BRIGHTNESS, MEASUREMENT
PROCEDURES AND PROPER SERVICE
ADJUSTMENTS.
WARNING:
HANDLEWITHCARE.HIGH
VACUUMPICTURETUBEISDANGEROUS
TO HANDLE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
REPLACE WITHATUBE OFTHE SAME
TYPENUMBERFORCONTINUEDSAFETY.
CAUTION:
TOMEASURE SECOND
ANODEVOLTAGEUSEAHIGHVOLTAGE
METERCONNECTEDFROMANODELEAD
TOCHASSISONLY. DISCHARGE HIGH
VOLTAGE TOCHASSISONLY,NOTTO
EXTERNALGROUND.
IREMITTER
NetCommand
R
DIGITAL
SERVICE
PORT
IEEE1394
INPUT/OUTPUT
AUDIO
ANT-2
AUX
ANT-1
MAIN
CableCARD
TM
SLOT
– (DTV/CABLE /VHF/UHF) –
S-VIDEO
VIDEO
INPUT
1 2
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
COMPONENT
YPbPr (480i/480p/1080i)
21
Y
Pb
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
DVI
DigitalVideo
DigitalAudio
AnalogAudio
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
MONITOROUTPUT
AUDIO2
TV back panel
AUDIO/VIDEO1
DigitalVideo
DigitalAudio
HD-6000 Receiver
Figure 11. Connecting an HDMI Device
HDMI Device
Figure 11
An HDMI-to-HDMI cable is required. This is not included with
the TV. It may be available at your local electronics retailer
Connect an HDMI cable from the TV back panel to the
HDMI device output. HDMI devices provide video and
audio through this cable, so no other connection is
required.