Filter
Top Products
35
VQT2J87 (ENG)
Reference
The images from this unit do not appear on
the television.
Picture is distorted.
¾
An incorrect resolution is selected in “Component Video
Resolution” or “HDMI Resolution”. Reset the setting as
follows:
1 While the unit is on, press and hold [OK], [B] and [Y] on
the remote control at the same time for more than
5 seconds.
– “00 RET” is displayed on the unit’s display.
2 Repeatedly press [1] (right) on the remote control or
[POWER Í/I] on the unit until “04 PRG” is displayed on
the unit's display.
3 Press and hold [OK] on the remote control or [< OPEN/
CLOSE] on the unit for at least 3 seconds.
Set the item again. (> 32)
– When Dolby Digital Plus, Dolby TrueHD, and DTS-HD audio
are not output in bitstream, select “Yes” in “Restore Default
Settings” and make proper settings. (> 33)
Video is not output.
¾
Set the “High Clarity Sound” in the Playback menu to “Off”
to use the COMPONENT VIDEO OUT terminal or the
VIDEO OUT terminal. (> 29)
¾
Video from the HDMI SUB AV OUT terminal is not output
when the “HDMI(SUB) Output Mode” is set to “V.OFF”.
(> 32)
Video is not output in high-definition.
¾
Confirm that the “HDMI Video Mode”, “HDMI Resolution”,
and “Component Video Resolution” in the Setup menu are
set properly. (> 32)
3D video is not output.
¾
Is there a non-3D compatible amplifier/receiver connected
between this unit and a TV? (> 10)
¾
If there is a non-3D compatible amplifier/receiver
connected to the HDMI SUB AV OUT terminal, set the
“HDMI(SUB) Output Mode” to “V.OFF”. (> 10)
¾
Are the settings on this unit and the TV correct? (> 23)
¾
Is the amplifier/receiver connected to between this unit
and TV on?
No subtitles.
¾
When progressive output is on, closed captions/subtitles
cannot be displayed.
The subtitles overlap closed captions
recorded on discs.
¾
Turn off the subtitles or turn off the closed caption setting
on the TV. (> 28)
A black band is displayed around the edge of
the screen.
The aspect ratio of the screen is abnormal.
¾
Confirm the “TV Aspect” is set properly. (> 32)
¾
Adjust the aspect setting on the television.
(Adjustment using “Screen Aspect” (> 20) on the unit is
also possible)
Cannot switch audio.
¾
When connecting an amplifier/receiver using a COAXIAL/
OPTICAL terminal or an HDMI terminal, you cannot
switch the audio if “Digital Audio Output” is set to
“Bitstream”. Set “Digital Audio Output” to “PCM” or
connect using AUDIO OUT terminal. (> 11, 31)
Cannot hear the desired audio type.
¾
Check the connections and the “Digital Audio Output”
settings. (> 31)
¾
When the unit is connected to an amplifier/receiver with
the AUDIO OUT terminal, set “Analog Audio Output”.
(> 32)
¾
To output audio from a device connected with an HDMI
cable, set “HDMI Audio Output” to “On” in the Setup
menu. (> 32)
¾
When connecting this unit to a TV via an HDMI MAIN AV
OUT and to an amplifier/receiver via an HDMI SUB AV
OUT, set “HDMI(SUB) Output Mode” to “V.OFF”. (> 10)
Picture
Audio
VQT2J87~Body_eng.fm 35 ページ ２０１０年１月２６日 火曜日 午後２時４１分