Filter
Top Products
22
SP ON SP OFF
CH DATE ON OFF
SP2 13:45 14:1527SA
CATEGORY
CH DATE ON OFF
SP–– 13:45 14:1527SA
CATEGORY
END:G-CODE
---------
G-CODE
SET:OK
END:G-CODE
PROGRAMME
123456
---
G-CODE
On Screen Display
END : MENU
CATEGORY SETTING
≥MOVIE
≥MUSIC
≥DRAMA
≥EDUCA
≥DOCUM
≥SPORT
≥CHILD
≥NEWS
≥OTHER
≥
–––––
END : MENU
CATEGORY SETTING
≥MOVIE
≥MUSIC
≥DRAMA
≥EDUCA
≥DOCUM
≥SPORT
≥CHILD
≥NEWS
≥OTHER
≥
–––––
CH DATE ON OFF
SP2 13:45 14:1527SA
CHECK
: PROG./CHECK
4 Press the Cursor button (1) S to select the Category.
Then, select the desired category by pressing the
Cursor buttons (3421) S.
– Alternatively, you can set the category on the Navigator
list. (See page 23 for details.)
– This function is activated when [JET NAVIGATOR] is set
to [ON]. (See page 13.) When [JET NAVIGATOR] is set
to [OFF], procced to the step 6.
5 Press the MENU button U to
make the previous display appear.
6 Press the TIMER (REC) button A to switch the VCR
over to the timer recording standby mode.
– When [JET NAVIGATOR] is set to [ON], the
[PROGRAMME IS COMPLETE. REMAINING
PROGRAMME 49.] message appers. (See page 13.)
– When [JET NAVIGATOR] is set to [OFF], the
[PROGRAMME IS COMPLETE.] message appears.
(See page 13.)
– Check that [Á] is lit on the VCR display.
If it is flashing, check the timer recording details again.
(See page 21.)
Notes:
– When the G-Code number is used for programming, the
recording time may be slightly longer than the actual
programme time.
– Repeat steps 2 and 3 if [PROGRAMME IS INCOMPLETE.]
appears.
– When programming two or more programmes, repeat
steps 1–6.
– The procedures for checking and cancelling a timer
programme are the same as on page 21.
To Suspend the Timer Recording Standby
Mode
See page 20.
G-Code Programming
Programming is now easier than ever; simply enter the
G-Code number found in the programme scheduling pages
of newspapers and magazines.
G-Code numbers are numbers assigned to programmes
listed in the TV programme schedule found in newspapers
and TV guides. When these numbers are entered, the
numbers are converted to actual programming.
G-
CODE is a registered trademark of Gemstar
Development Corporation. The G-
CODE system is
manufactured under licence from Gemstar Development
Corporation.
Preparations
– Confirm that the VCR is on.
– Confirm that the TV is on and the VCR viewing channel is
selected.
– Insert a video cassette with an intact erasure prevention
tab.
– Set the VCR/TV switch E to [VCR].
– Check that the clock is set to the correct time. If it has not
been set, refer to page 10.
Example:
Programming a timer recording of a TV programme with the
G-Code number 123456
Operations
1 Press the G-CODE/SV button H to
display the menu for entering the
G-Code number on the TV.
2 Press the Numeric buttons 2 to
enter the G-Code number.
– It is also possible to check the
number with VCR display without
appearing the On Screen Display.
– If you have entered the wrong number, press the
CANCEL button ; then enter the proper number. An
alternative method is to press the Cursor button (2) S
and then enter the proper number.
3 Press the OK button T.
– The entered programme appears
on the display.
– The starting time and the ending
time appears alternately each
5 seconds on the VCR display.
– Confirm that the number
corresponds to the right
programme. If the display looks
like this and Á on the VCR
display flashes on and off: select
the desired programme position
using the Channel button 9, then
press the OK button T.
– To make any corrections, use the DATE button :, the
ON button D, the OFF button C and the SPEED button
B the same way as described on page 19.