Filter
Top Products
24
To Change a Timer Recording
Programming
It is not possible to change a programming while the timer
recording is being performed.
≥ Display the VCR picture on the TV.
≥ Set the VCR/TV switch P to “VCR”.
1 Press the PROG./CHECK button < to display the timer
recording programmings on the TV screen.
2 Press the Cursor buttons (34) R to select the
programming that you want to change.
3 Follow the operations below to change the programmed
contents.
To change the broadcasting station:
Use the Channel buttons :.
To change the date of
the timer recording:
Use the DATE button ;.
To change the recording
starting time:
Use the ON button G.
To change the recording ending time:
Use the OFF button F.
To change the recording speed:
Use the SP/LP button E.
4 Press the OK button T to conclude the setting.
5 Press the EXIT button S to exit the On Screen Display.
Timer recording
Pos Start Stop SP VPS
Name DATE ON OFF LP PDC Min
ZDF 27/10
We
20:00 21:30 SP ON 90
ARD 30/10 Sa 19:00 20:00 LP ON 60
N3 Su 21:00 23:30 SP ON 150
ZDF
Su-Sa
17:30 18:00 EP ON 30
jjjjj jj
/
jj jj jj
:
jj jj
:
jj jj jjj jjj
jjjjj jj
/
jj jj jj
:
jj jj
:
jj jj jjj jjj
jjjjj jj/jj jj jj:jj jj:jj jj jjj jjj
jjjjj jj jj jj jj jj jjjj jj jjj jjj
To Check the Contents of Timer Recording
Programmings
≥ Display the VCR picture on the TV.
≥ Set the VCR/TV switch P to “VCR”.
1 Press the PROG./CHECK button < to display the timer
recording programmings on the TV screen.
≥ When the VCR is in the timer recording standby
mode for a VPS/PDC recording, the On Screen
Display may be distorted.
2 Press the EXIT button S to exit
the On Screen Display.
Timer recording
Pos Start Stop SP VPS
Name DATE ON OFF LP PDC Min
ZDF 27/10
We
20:00 21:30 SP ON 90
ARD 30/10 Sa 19:00 20:00 LP ON 60
N3 Su 21:00 23:30 SP ON 150
ZDF
Su-Sa
17:30 18:00 EP ON 30
jjjjj jj
/
jj jj jj
:
jj jj
:
jj jj jjj jjj
jjjjj jj jj jj jj jj jjjj jj jjj jjj
jjjjj jj jj jj jj jj jjjj jj jjj jjj
jjjjj jj jj jj jj jj jjjj jj jjj jjj
Notes for Programming a Timer Recording of a Satellite
Programme:
≥ When programming a timer recording of a satellite
programme, it is not possible to activate the VPS/PDC
function.
≥ On some satellite receivers, the power may be turned off for
a few seconds before a timer recording is actually started
and recording may not be performed for those first few
seconds. To ensure recording from the beginning of the
programme, we recommend that you set the recording start
time about a minute earlier than that listed in the
newspaper/magazine.
≥ After the timer recording has finished, some satellite
receivers switch off automatically, but the recording has
been performed as programmed.
≥ If a power failure occurs during the timer recording of a
satellite programme, the timer recording may not resume
when the power is restored.
≥ Timer recording of pay-per-view satellite programmes is not
possible.
≥ Timer recording of satellite programmes from a satellite
receiver or satellite receiver channel for which the PIN code
has been entered is not possible.
≥ Timer recording of satellite programmes for which the
parental control function has been activated is not possible.
Programming a Timer Recording of a
Satellite Programme
The programming of a timer recording of a satellite
programme can be performed in the same way as for normal
(terrestrial) TV programmes.
For the connection to a satellite receiver and the necessary
settings, refer to pages 41 to 43.
Conditions for correct operation of this function:
≥ When selecting the programme position, be sure to use the
Numeric buttons 2 to select the satellite channel.
Timer recording
Pos Start Stop SP VPS
Name DATE ON OFF LP PDC Min
AV2 SAT19
pp
:
pp pp
:
pp
SP
ppp ppp
ppppp
pp
/
pp pp pp
:
pp pp
:
pp pp ppp ppp
ppppp
pp
/
pp pp pp
:
pp pp
:
pp pp ppp ppp
ppppp
pp
/
pp pp pp
:
pp pp
:
pp pp ppp ppp
ppppp
pp
/
pp pp pp
:
pp pp
:
pp pp ppp ppp
ppppp
pp
/
pp pp pp
:
pp pp
:
pp pp ppp ppp
ppppp
pp
/
pp pp pp
:
pp pp
:
pp pp ppp ppp
ppppp
pp
/
pp pp pp
:
pp pp
:
pp pp ppp ppp
SAT 9:
SAT 19:
SAT
0
SAT
0
1 9
SAT
0
9
2 9
SAT
0
1
SAT 129:
Example of selecting satellite programme
positions 9, 19 and 129:
3-digit programme positions can be selected with this
remote control only in case of a satellite receiver that is
marked with (°
1
) on the enclosed list of compatible
satellite receivers.