Filter
Top Products
22
EXAMPLE: One-touch Timer Recording for 30 minutes.
Timer recording can be programmed on-screen with
the remote control. The built-in timer allows automatic
unattended recording of up to 8 programs within 1
month.
EXAMPLE: Program a timer recording for 23rd day, channel
007 (CATV), 7:00 - 9:30 PM (Tape speed : SLP).
• Load a video cassette with the erase prevention tab
intact. The TV/VCR will automatically turn on.
• Set the TV/CATV selection to the appropriate position
(See page 16).
TIMER REC SET
+/–/ENTER/CANCEL/MENU
DATE
START
END
CH
SPEED
23 (THU)
8
:
30 AM
--
:
--
012
SP
〈
+/–/ENTER/CANCEL/MENU
〉
----- --
:
-- --- -
----- --
:
--
--
:
--
--
:
--
--
:
--
--
:
--
--
:
--
--
:
--
----- --
:
-- --- ---
:
--
--
:
--
--
:
--
--
:
--
--
:
--
--
:
--
--
:
--
--- -
----- --- -
----- --- -
----- --- -
----- --- -
----- --- -
NOTES: • If programming is performed without a tape in
the TV/VCR, or with a tape without an erase
prevention tab, the Timer Recording is not
possible. If a tape without an erase prevention
tab is in the TV/VCR, the tape will be ejected.
• To record from the external equipment press
the SET/TRACKING + or – button repeatedly
until "L 1 (from AUDIO/VIDEO LINE1 jacks on
the rear)" or "L 2 (from AUDIO/VIDEO IN jacks
on the front)" appears when setting the
channel in step 5.
• The VCR section cannot be used while the
PROG TIMER indicator is lit. If you want to use
the VCR operation, press the
PROG TIMER
button to deactivate the timer.
• After a power failure or disconnection of the
power plug, all programmed recording setting
and time display will be lost upon resumption of
power. In this case, reset the clock (see pages
13-14) and reprogram any timer recordings.
• If you want to correct the digits while setting,
press the CANCEL button until the item you
want to correct, then press the SET/TRACKING
+ or – button to correct the desired setting.
3 Press the SET/TRACKING + or –
button to select the program
position, then press the ENTER
button.
4 Press the SET/TRACKING + or –
button to select the date, then
press the ENTER button.
5 Set the start time, end time,
channel and tape speed as in step 4.
The One-Touch Timer Recording feature provides a
simple and convenient way to make a timed recording.
ONE-TOUCH TIMER
RECORDING
(
OTR
)
5 Press the Direct Channel Selection buttons or CH C
or D button to select the channel to be recorded.
6 Press the REC/OTR button to
begin recording. Press the button
again to stop recording after 30
minutes. Each additional press of
the REC/OTR button will increase
recording time as shown below,
up to a maximum of 5 hours.
“OTR” will appear on the screen.
NOTES: • Press the REC/OTR
button to increase the
time needed for recording
(See the chart right).
• To cancel OTR, press
the STOP button.
• The TV/VCR channel
cannot be changed
during recording.
1 Press the POWER button to turn on the TV/VCR.
2 Load a video cassette with the erase prevention tab
intact.
3 Press the SPEED button to
select the desired tape speed
(SP or SLP). SP or SLP will
appear on the screen.
4 Set the TV/CATV option to the
appropriate setting (See page 16).
OTR 0 : 30
CH 012
00
:
00
:
00 SP
〈
+/–/ENTER/CANCEL/MENU
〉
----- --
:
-- --- -
----- --
:
--
--
:
--
--
:
--
--
:
--
--
:
--
--
:
--
--
:
--
23 TH
007
--
:
--
--
:
--
--
:
--
--
:
--
--
:
--
--
:
--
--- -
----- --- -
----- --- -
----- --- -
----- --- -
----- --- -
7:00
PM
9:30
PM
SLP
TIMER REC SET
〈
+/–/ENTER/CANCEL/MENU
〉
DATE
START
END
CH
SPEED
23 (THU)
7
:
00 PM
9
:
30 PM
007
SLP
TV - VHF/UHF channels
CATV - CABLE TV channels
Press
once
twice
3 times
4 times
5 times
6 times
7 times
8 times
9 times
Recording time
NORMAL REC
0:30
1:00
1:30
2:00
3:00
4:00
5:00
NORMAL REC
TIMER RECORDING
1 Press the MENU button.
2 Check the TIMER REC SET
option is selected, then press
the ENTER button.
M E N U
TIMER REC SET
TV SETUP
CH SETUP
AUTO REPEAT ON OFF
SYSTEM SETUP
+/–/ENTER/MENU
6 To set the timer for another program, press the SET/
TRACKING + or – button until the number of the
second program blinks, then press the ENTER
button. Repeat steps 4 to 5 to set the second pro-
gram.
7 Press the PROG TIMER button. The PROG TIMER
indicator will light. The Timer is programed, when the
programed time is reached, the recording is automati-
cally started.
To cancel timer recording, press the button again and
PROG TIMER indicator will go out.
TIMER RECORDING
5B02301A E P20-Back 9/4/03, 11:42 AM22