Filter
Top Products
C1301M (6/05) 9
Quick Start Guide – System Setup
Quick Programming Guide
Access the main menu (preset 95). Refer to
Accessing Main Menu (Preset 95) section.
Use the joystick to position the cursor beside
menu selection. If your controller does not have a
joystick, use the up or down key.
Press Iris Open; the submenu/cursor moves to the right.
Move the joystick up or down to view selections. If
your controller does not have a joystick, use the up
or down key.
Press Iris Open to make selection.
Press Iris Close to cancel selection.
Presets
The following presets are reserved for special functions.
Preset Function
86 Wiper
87 Washer
88 IR filter IN (color)
89 IR filter OUT (black-white)
95 Select main programming menu
NOTE: For American Dynamics controllers with only 32 presets, switch SW3-1
on the dome drive to the ON position. When SW3-1 is ON, preset
95 becomes 28
89 becomes 22
88 becomes 21
WIPER**
WIPER CONTROL
WIPER MODE
WIPER DWELL (SECS)
WIPER TIME (MIN)
<SET WASHER SEQUENCE>
BACK
EXIT
LYNE SYNC
LINE SYNC
LINE SYNC PHASE
BACK
EXIT
PATTERNS
PATTERN NUMBER
<PROGRAM PATTERN>
<CLEAR PATTERN>
BACK
EXIT
REFERENCE INFORMATION
PATTERN USAGE
REMAINING
ALARMS
RESUME
SEQUENCE (SECS)
RESET DELAY (SECS)
<ALARM SETTINGS>
BACK
EXIT
POWER UP
POWER UP ACTION
BACK
EXIT
AUX
AUX 1 MODE
DWELL TIME (SECS)
AUX 2 MODE
DWELL TIME (SECS)
BACK
EXIT
CLEAR
CLEAR ALL PRESETS
CLEAR ALL PATTERNS
CLEAR ALL WINDOW BLANKING
RESTORE FACTORY DEFAULTS
BACK
EXIT
OTHER
PARK TIME (MINUTES)
PARK ACTION
BACK
EXIT
ADVANCED SETTINGS
* Available only with the 23X day/night camera.
** Available only with wiper models.
SHUTTER SPEED
AGC LIMIT
AUTO IRIS
AUTO IRIS LEVEL
AUTO IRIS PEAK
AUTO SHARPNESS
SHARPNESS LEVEL
AUTO WHITE BALANCE
R GAIN
B GAIN
BACKLIGHT COMP
VIDEO LEVEL
WIDE DYNAMIC RANGE*
BACK
EXIT
SET WINDOWS
WINDOW NUMBER
<EDIT WINDOW LOCATION>
<EDIT WINDOW ZOOM>
ENABLE WINDOW
REVERSE
CLEAR WINDOW
BACK
EXIT
ALARM SETTINGS
ALARM NUMBER
ALARM PRIORITY
ALARM ACTION
ACTIVATE AUX
ALARM CONTACT
BACK
EXIT
UNIT SETTINGS
<CAMERA>
<OTHER>
<POWER UP>
<LINE SYNC>
<PRESETS>
<PATTERNS>
<WINDOW BLANKING>
<ALARMS>
<WIPER>
<AUX>
<CLEAR>
<PASSWORD>
BACK
EXIT
ADDITIONAL
FREE MEMORY
LAST RESET
CAMERA ACTIVE
FPGA VERSION
VIDEO LEVEL
<CAMERA>
<EAB>
<PMAB>
LANGUAGE 1
LANGUAGE 2
LANGUAGE 3
LANGUAGE 4
LANGUAGE 5
LANGUAGE 6
LANGUAGE 7
LANGUAGE 8
LANGUAGE 9
LANGUAGE 10
BACK
EXIT
SYSTEM INFORMATION
UNIT MODEL
POWER MODULE MEMORY
SOFTWARE VERSION
BIOS VERSION
FONT VERSION
COMM
D ADDRESS
P ADDRESS
CM9500 MODE
32 PRESETS
PROTOCOL
<ADDITIONAL>
BACK
EXIT
LABEL POSITION
[PRESET LABEL- - - ---]
[ALARM 1- - - - - - -]
SAVE AND EXIT
CANCEL AND EXIT
HELP
XXX.XXX
DISPLAY SETUP
PRESET LABEL
ZOOM
ALARM MESSAGE
<LABEL POSITIONS>
RESTORE FACTORY DEFAULTS
BACK
EXIT
PELCO EXSITE EHXM
LANGUAGE
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<UNIT SETTINGS>
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
EXIT
CAMERA
TYPE OF LIGHTING
AUTO FOCUS
ZOOM LIMIT
ZOOM SPEED
LOW LIGHT LIMIT
IR CUT FILTER*
AUTO IR LEVEL*
<ADVANCED SETTINGS>
BACK
EXIT
PASSWORD
ENABLE PASSWORD
<EDIT PASSWORD>
BACK
EXIT
SET WASHER SEQUENCE
PRESET NOT DEFINED
<EDIT PRESET LABEL>
<EDIT PRESET SCENE>
<EDIT CAMERA SETTINGS>
WASHER TIME (SECS)
WIPER DELAY (SECS)
AUTO RETURN
<CLEAR PRESET>
<CLEAR CAMERA SETTINGS>
BACK
EXIT
EDIT DETECTION AREA*
DETECTION AREA 1
LOCATION
SENSITIVITY
DETECTION AREA 2
LOCATION
SENSITIVITY
DETECTION AREA 3
LOCATION
SENSITIVITY
DETECTION AREA 4
LOCATION
SENSITIVITY
BACK
EXIT
MOTION DETECTION*
MOTION DETECTION ENABLED
<EDIT DETECTION AREA>
ACTIVATE AUX
AUX TIME
BACK
EXIT
PRESETS
PRESET NUMBER
PRESET NOT DEFINED
<EDIT PRESET LABEL>
<EDIT PRESET SCENE>
<EDIT CAMERA SETTINGS>
<MOTION DETECTION>*
<CLEAR PRESETS>
<CLEAR CAMERA SETTINGS>
BACK
EXIT
WINDOW BLANKING
STYLE
<SET WINDOWS>
BACK
EXIT
EDIT THE PASSWORD
- - - - - - - - - - - - - - - - -
1234567890 OK
ABCDEFGHIJ CANCEL
KLMNOPQRST
UZWXYZ.,-/ SPACE
abcdefghij BACKSPACE
klmnopqrst
uvwxyz*;: