Filter
Top Products
15
English
Remote Control Overview
See Figure 2
The RDV-1093 is supplied with an RR-DV98
remote control that duplicates the front-panel
functions and provides additional features.
Remote Control Batteries
Three R03(LR03)/AAA size batteries (supplied)
must be installed before the remote can be
used. Remove the cover on the back of the
RR-DV98. Install the batteries following the
polarity symbols, then replace the cover.
NOTE: Remove the batteries from the re-
mote if it will not be used for a long period
of time. Do not leave run down batteries in
the remote control; they can leak corrosive
chemicals which will damage the unit.
Using the Remote
To use the remote, aim it at the remote sensor
on the front-panel of the RDV-1093. The opera
-
tion of the remote sensor can be affected if it
is blocked or exposed to bright infrared light.
In addition, remote control functions may not
work reliably if the batteries in the RR-DV98
are weak.
ON/OFF Buttons
These two buttons provide discrete ON/OFF
functions. Press the ON button to activate the
RDV-1093 and the OFF button to put the unit
in standby mode.
NOTE: The front panel master power button
must be pressed in for the remote ON/OFF
buttons to work.
OPEN/CLOSE Button
Pressing this button opens or closes the Disc
Drawer. If in standby mode, pressing the button
activates the unit.
PLAY Button
The PLAY
/
button duplicates the function of
the front panel PLAY
/
button and is used to
confirm selections in menus. Press this button to
start playing the disc from the beginning or to
resume play if playback is paused or to return
to normal play from any of the slow motion or
fast play modes. If in standby mode, pressing
the button activates the unit.
STOP Button
Press the STOP
.
button to stop a disc that is
playing. If playback is restarted after one press
of the button, the disc will resume playing from
the current position on the disc. Press the button
twice to cancel the resume feature. Subsequent
play will restart from the beginning of the disc.
Playback will also stop when the OFF button
on the remote is pressed.
PAUSE Button
Press the PAUSE
,
button to temporarily suspend
play or to advance the still picture frame by
frame after playback is paused.
TRACK Buttons
The TRACK
{
}
buttons skip forward/back
to the beginning of the next selection.
SEARCH Buttons
During playback, press the SEARCH
[
]
buttons to begin high-speed play, either
forward or reverse, at 2X, 4X, 8X, 16X, 30X,
or 60X normal speed, increasing with each
additional press. Press the PLAY
/
button to
resume normal speed playback.
Numeric Buttons
These buttons (1–0 and +10) are used for
direct entry of specific Chapters, Titles, and
times. Two digit numbers are typically entered
by pressing +10 followed by the next digit, as
detailed in operating steps.
CURSOR Buttons
Use the four CURSOR t/u/p/q buttons to
navigate the on-screen display menus.
The left/right CURSOR
t/u buttons are also
used for Program play mode (CD only).
ENTER Button
This button (labeled ENT) is used to confirm
many selections in operating the RDV-1093.
We refer to this button as the ENTER button
throughout this manual.
MENU Button
Press the MENU button to activate the menu
on the disc.
The MENU button is also used to clear the
Program play menu (CD only).
SETUP Button
Press this button to access the Main Menu screen
used in the setup of the RDV-1093.
DISPLAY Button
The DISPLAY button changes the time shown
in the front panel display and shows a time
display in the Status Bar display. Several op
-
tions are available including elapsed time and
remaining time of individual Chapters/Tracks
or entire Disc/Titles.
TITLE Button
Press the TITLE button to activate the submenu
for the current Title. On some discs, this but
-
ton will activate the same root menu as the
MENU button.
SLOW Button
Press this button to select slow motion play,
either forward or reverse, at 1/2, 1/4, or
1/8 normal speed.
The SLOW button is also used to view still
pictures on a DVD-Audio disc. Each press of
the button advances to the next picture.
GOTO Button
Press the GOTO button for direct selection of
a particular Time, Title, or Chapter with the
NUMERIC buttons. The first press of the GOTO
button allows direct entry of Time. Press the
GOTO button a second time for direct entry
of a Title number. A third press allows direct
entry of a Chapter.
For example, to select Chapter 5, press the
GOTO button three times to reach the Chapter
entry mode. Then press 0 followed by 5. Press
the PLAY
/
or ENT button to begin playback
at the selected point.
ANGLE Button
Press the ANGLE button to select an alter-
nate angle view (if available for the current
scene).
NOTE: “Operation not possible” displayed
in the status bar indicates that this feature is
not available for the current scene.