Filter
Top Products
9 English
Connecting the Power Cord
When all the connections have been made,
insert the power plug into the wall outlet firmly.
The STANDBY indicator lights and setup is
complete. Observe the following precautions.
• Disconnect the power cord if you are not
going to use the unit for a long time.
• Disconnect the power cord before clean-
ing the unit.
• Disconnect the power cord before moving
the unit.
• Do not connect or disconnect the power cord
with wet hands.
• Do not pull the power cord when discon-
necting it, as this may damage the cord and
cause fire, electric shock, or other accidents.
• Do not damage, alter, twist, or pull the power
cord, as this may cause fire, electric shock,
or other accidents.
• Contact a dealer and get a new power cord
if the cord is damaged. A damaged cord
may cause fire, electric shock, or other ac-
cidents.
• Do not put anything heavy, or the unit, on
the power cord, as this may cause fire, elec-
tric shock, or other accidents.
RR-DV91 Remote Control
Installing the Batteries
The battery compartment is located on the back
of the remote control unit.
1 Press down on the point shown by the ar-
row at the top of the compartment cover,
and pull up the cover to open the compart-
ment.
2 Place the two accessory R6P (SUM-3)/
AA(15F) batteries in the remote control ac-
cording to the polarity markings (“+” and
“–”) inside the compartment and on the bat-
teries.
3 Place the cover over the compartment, and
press down lightly.
The batteries will last about six months with
normal use. If the functions of the remote control
become erratic, replace the batteries.
Precautions for the safe use
of batteries
Observe the following precautions for the safe
use of batteries. If they are used improperly
their life will be shortened, they may burst or
their contents may leak.
• Remove the batteries from the remote control
if it is not going to be used for a long pe-
riod of time.
• Remove dead batteries and dispose of them
properly.
• Never leave dead batteries lying around,
take them apart, mix them with other refuse,
or throw them into an incinerator.
• Never touch liquid that has leaked out of
a battery.
• Do not mix new and old batteries, or bat-
teries of different types, when replacing
them.
Programming the RR-DV91
Remote to Control a TV
You can operate your TV from the remote
control unit. The remote must first be pro-
grammed to operate your TV set.
1 Press and hold down the TV/VIDEO
14
button. Then enter the manufacturer code
of your TV listed below by using the nu-
meric buttons (0 - 9)
13
. Do not release
TV/VIDEO. Keep holding it until the next
step is completed. (Example: To enter code
“01” press and release the “0” button, then
press and release the “1” button.
2 Press the STOP button, then release the
TV/VIDEO button.
No. Manufacturer
01 JVC
02 Magnavox
03 Mitsubishi
04 Panasonic
05 RCA
06 Sharp
07 Sony
08 Toshiba
09 Zenith
10 Hitachi
11 Panasonic
12 Samsung
13 Sanyo
14 Sanyo
15 Samsung
3 Test the program setting by pressing the TV
POWER
17
button to see if it turns your
set on. If there is more than one code listed
for the manufacturer of your TV, try them
one by one until you succeed.
Remote Control TV Operation
The following buttons can be used for oper-
ating the TV (The numbers in brackets are those
shown on figure 1 on page 3.)
TV POWER
17
Turns the TV on or off.
TV CH
29
Changes the TV channels.
TV VOL
28
Adjusts the TV volume.
0 - 9 (Numeric Buttons)
13
Selects the TV channels (while holding down
the SHIFT button). Note: For some TVs, pressing
“+10” while holding down SHIFT functions as
the “RETURN,” and pressing “10” while hold-
ing down SHIFT functions as the “– /– –” but-
ton.
TV/VIDEO
14
Switches input mode (either TV or VIDEO).