Filter
Top Products
- 4 -
✎ By connecting the TV to a receiver or home theater with
Dolby Digital and 5.1ch speakers and selecting Dolby
Digital, you can maximize your interactive 3D sound
experience.
■
Audio Delay: Lets you correct timing mismatches between the
audio track and the video when you are watching the TV and
listening to digital audio output from the TV through an external
device such as an AV receiver. When you select Audio Delay, a
slider appears. Use the left and right arrow buttons to adjust the
slider. Press ENTER
when done (0ms ~ 250ms).
Speaker Settings
■
Speaker Select (External Speaker / TV Speaker)
If you are listening to the sound track of a broadcast or movie
through an external receiver, you may hear a sound echo caused
by the difference in decoding speed between the TV’s speakers
and the speakers attached to your audio receiver. If this occurs, set
the TV to External Speaker.
✎ When you set Speaker Select to External Speaker, the
TV’s speakers are turned off. You will hear sound through the
external speakers only. When you set Speaker Select to TV
Speaker both the TV’s speakers and the external speakers
are on. You will hear sound through both.
✎ When Speaker Select is set to External Speaker, the
VOLUME and MUTE buttons will not operate and the sound
settings will be limited.
✎ If there is no video signal, both the TV’s speakers and the
external speakers will be mute.
Sound Reset
■
Reset All: Resets all sound settings to the factory defaults.
Channel Menu
❑ Memorizing Channels
When you first set up your TV using Plug & Play, the TV memorized
the channels that were available over the air or through your cable
system and added them to the Channel List. The Antenna and
Auto program functions described below let you re-run the channel
memorization function without having to re-run the Plug & Play
procedure.
Antenna (Air / Cable)
Before your television can memorize the available channels, you
must select your TV's signal source, Air (using an antenna) or Cable.
Select Menu >Channel > Antenna > Air or Cable. After you have
selected the signal source, go on to the Auto Program function.
✎ Selecting the signal source using the Antenna function also
determines the signal source the TV is tuned to. For example,
if you receive your TV signal over the air, and you select Cable,
you will see only snow. You must select Air to see a picture.
Auto Program
The Auto Program function memorizes all channels that are
available over the air or through your cable system and adds them to
the Channel List.
To start Auto Program, follow these steps:
1. Push MENU
→ Channel → ENTER
on your remote. The
Antenna Source screen appears.
2. On the Antenna Source screen, select the source of your TV
signal.
Air
If your TV is connected to an antenna choose Air, and then press
ENTER
. The TV will automatically start memorizing channels.
Cable
If your TV is connected to a cable outlet, choose Cable, and then
press ENTER
. Go to Step 3.
Auto
If you choose Auto, and then press ENTER
, the TV will
automatically select the correct Antenna source. Go to Step 3.
3. On the Cable Type screen, use the ◄/►/▲/▼ buttons to select
the type of digital and analog cable systems you have: STD, HRC,
or IRC. Most systems are STD (Standard). When done, select
Start, and then press ENTER
. The TV will start memorizing
channels.
✎ Channel memorization can take up to 45 minutes, depending
on your cable system.
✎ Memorized channels are added to the Added Channel
list. These are the channels you will see when you use the
Channel buttons on your remote.
Clear Scrambled Channel
This function filters out scrambled channels after Auto Program is
completed. This process may take up to 20~30 minutes.
✎ Press the ENTER
button to stop the Clear Scrambled
Channel.
✎ This function is only available in Cable mode.
❑ Managing Channels
Channel List
See your list of Added channels, Favorite channels, or channels
you've scheduled for viewing. Add or delete Favorite channels, add
or delete channels from the Added Channels list, schedule channels
or programs for viewing. Watch a channel by selecting the channel
in the All Channels, Added Channels, or Favorite screen, pressing
the ▲ / ▼ buttons, and then pressing the ENTER
button.
Added Channels
6 Air
6-1 ♥ TV #6
7-1 ♥ TV #7
8 Air
9 Air
9-1 ♥ TV #9
10 Air
10-1 ♥ TV #10
11-1 ♥ TV #11
Air ' Zoom ' Select Tools ► Next Program
Channel List Screens icons are listed on the left side. Select an
icon using the ▲/▼ buttons to view each list.
■
All Channels: Shows all currently available channels including
those you deleted from the Added channels list.
■
Added Channels: Shows all Added channels. These are the
channels that appear when you press the CH button.
■
Favorite: Shows all favorite channels.
■
Programmed: Shows all channels and programs currently
scheduled using Timer Viewing.
✎ Remote control buttons active on the Channel List screen.
x Green (Zoom): Enlarges or shrinks a channel number.
x Yellow (Select): Move the cursor to a channel. Press the Yellow
button to select the channel. A
mark appears. Repeat to select
additional channels. Then, open the Tools menu and apply a
function to the channels you selected.
x
(Tools): Displays the Channel List Tools menu. (The Tools
menus may differ depending on the situation.)