Samsung SCR-3000P DVR User Manual


 
4-16
4-15
DIGITAL VIDEO RECORDER
6
The following illustrates the intial setting of the SYSTEM SETUP menu.
PASSWORD
Set the system password. You can enter a 4-digit number and the initial set value is 0000.
PASSWORD LOCK
If you set this to ON, the system will ask for a password, which was set in PASSWORD,
when your press the MENU ( ) button or when you attempt to cancel the recording lock
while recording or when you attempt to remove the video tape from the video deck. If the
password is invalid, you will not be able to finish the desired operation. If you set this to
OFF, the system will not ask for a password for any of the operations above.[ON/OFF]
HDD ERASE
If you set to ON and exit the menu, the system will delete all data stored on the HDD.
[ON/OFF]
FACTORY RESET
If you set to ON and finish the menu, all settings will be restored to their factory default set-
tings. However, the data on the HDD will not be deleted. After RESET The message, “DO
YOU REBOOT SYSTEM?” will be displayed. Select YES to reboot the system. [ON/OFF]
MENU SCREEN
If this is set to DARK GRAY, the background of the screen becomes darker when the
MENU button is pressed and you will not be able to see the characters clearly. If set to OFF,
you can see the current video clearly even when the MENU button is pressed.
[DARK GRAY/OFF]
LANGUAGE
SCR-3000N/SSC-Dual models only supports English. SCR-3000P models however supports
German, French, Spanish, and Italian in addition to English.
There is a language support setting function for the convenience of international users. The
default language is set to English.
SCR-3000N/SSC-Dual [ENGLISH]
SCR-3000P [ENGLISH/DEUTSCH/FRANÇAIS/ESPAÑOL/ITALIANO]
IR REMOCON
If IR REMOCON to ON, signals from the remote control will be received and if it is set to
OFF, signals from the remote control will not be received. The option will be turned off by
factory default reset. For instructions on how to use the remote control, please refer to “4.
Introduction to the Remote Control” on page 1-7. [ON/OFF]
MULTIPLEXER
If MULTIPLEXER is set to WITHOUT, ID Detection will not be performed and the system
will recognize it as 1CH regardless. If MULTIPLEXER is set to WITH, the Video ID input
from the Multiplexer will be detected. Set MULTIPLEXER to WITH, and exit the MAIN
MENU (DVR) to automatically start the Multiplexer ID Detection. In addition, MULTI-
PLEXER SELECT will be enabled and MOTION DETECTION-related functions will be
disabled.
[WITHOUT/WITH]
MULTIPLEXER SELECT
If MULTIPLEXER is set to WITH, MULTIPLEXER SELECT will be enabled.
The settings of all recording modes will be dependent on the Multiplexer setting.
The corresponding Multiplexers are SAMSUNG SDM-160(SDM-090), SMO-150(SMO-
210, SOM-080).
SCR-3000N/SSC-Dual [SAMSUNG SDM-160 / SAMSUNG SMO-150]
SCR-3000P [SDM-160P / SAMSUNG VPP]
Caution
Caution
Verify once again that is is OK to delete the data, as deleted data cannot be restored.
Caution
Caution
Do not set the multiplexer option to [With] and fail to receive the multiplexer output
signal as input to avoid error in recording. Please set the multiplexer option to
[Without] whenile not receiving the multiplexer output signal as input.
Set the multiplexer option to [Without] unlessif the multiplexer manufacturer of the
multiplexer is not Samsung.
System Setup
SYSTEM SETUP
PASSWORD ****
PASSWORD LOCK OFF
HDD ERASE OFF
FACTORY RESET OFF
MENU SCREEN DARK GRAY
LANGUAGE ENGLISH
IR REMOCON OFF
MULTIPLEXER WITHOUT
MULTIPLEXER SELECT SAMSUNG SDM-160
MOVE=[//
/
] SELECT=[ ] EXIT=[MENU]
MENU