Filter
Top Products
15
Many of your TV’s functions are controlled through the menu function.
During menu operation a bar at the bottom of the screen show which
controls can be used.
Press the u button to enter and exit the 5 sub menus Picture,
Sound, Timer, Setting and Preset.
When a sub menu is selected its options are displayed and its colour
will change to yellow.
When you have set each Sub menu you can either press the MENU
button to exit and clear the screen or press the 5 button until the
sub menu is re-selected. Using the
7,8 button you can rotate again.
Press the 7 or 8 button and select Picture menu, set the picture
settings for your personal preference.
Use the e or d button to select eg. Brightness and the 7 or 8
button to adjust levels.
Tint : is only available if NTSC equipment is connected.
Text brightness : you can set to Minimum, Centre or Maximum.
Use the
e or d button to select and the 7 or 8 button to set.
To memorise these settings press the
F/OK button. (The OK? will
change to OK.)
To exit press the MENU button.
Press the
MENU button and select Sound menu by pressing the 7
or 8 button.
Select and adjust to obtain the best sound settings for your environment
using e or d and 7 or 8 button.
To exit press MENU button.
■ Off-timer setting
The Off timer will switch the TV set into the standby mode when the
selected time has elapsed.
1. Press the MENU button and select Timer using 7 or 8 button.
Select OFF Timer using the e or d button. The complete line
turns yellow.
2. Press the 7 or 8 button to select --:-- (highlighted yellow).
3. Press the e or d button to change time.
The time changes in 30 minute steps.The maximum time is 2:00hrs.
4. Press the 7 or 8 button to highlight complete line (yellow).
5. Press the OK button to store your settings.
If you have set the off timer, then one minute before the TV switches
off, a display appears on the screen.
✐ If the TV set is switched off by the standby button on the remote
control or by the standby switch on the front of the TV set the
timer settings will be cancelled.
Press the MENU button to exit, or press the 7 button to highlight
complete line yellow and then press the d button to set Alarm timer.
■ Alarm timer setting
This function can be set so that an alarm goes off. This only hap-
pens when the TV is switched on. It may remind you to do something.
1.
Press the MENU button and select Timer using the 7 or 8
button. Select Alarm timer using the e or d button. The complete
line turns yellow.
2.
Press the 7 or 8 button to select --:--.
3. Press the e or d button to change time.
The display changes in 5 minute steps and the maximum time period
is 3:00 hours.
4. Press the 7 or 8 button to highlight complete line (yellow).
5. Press the OK button to set the Alarm.
When the time period is up, the time up signal will appear on the
screen and the alarm will sound for 15 seconds.
To cancel the Alarm timer press any button and the display will
disappear.
✐ If the TV set is switched off by the standby switch on the remote
control, the standby switch on the front of the TV or a power failure
occurs the timer settings will be cancelled.
MENU OPERA
MENU OPERA
TION -
TION -
Analogue channels
Analogue channels
Picture menu
Sound menu
Auto Tuning
Auto sort Start
Prog. Preset
Swap
Fine Tuning
Brightness
Contrast
Colour
Sharpness
Tint (only if NTSC equipment is detected)
Text brightness
Memory
Picture
MENU
Sound
Timer
Volume
Bass
Treble
Balance
BBE
OFF Timer
Alarm Timer
Setting Child lock
AV2
Noise Reduction
ON/OFF
Video/S-video
ON/OFF
Preset
Auto Channel
Position
Semi
Channel
Position
Skip
Memory
Picture
Memory
Text brightness
Tint
Sharpness
Colour
Contrast
Minimum/Centre/Maximum
OK? / OK
42
19
2
27
Brightness
38
OFF timer
Alarm timer
Timer
Sound
Balance
Treble
Bass
Volume
12
0
0
0
BBE
ON / OFF
eg.
Timer menu
- - : - -
Timer
Alarm timer
OFF timer
- - : - -
OK?