Sanyo SRT-4040 VCR User Manual


 
ON-SCREEN MENU
WARNING OUT/CONTROL SET menu
<WARNING@OUT@SET>SET@UP
ALARM@@@@@@@@@@@@Y
NON@REC@@@@@@@@@@N
MECHA.PROBLEM@@@@Y
VIDEO@LOSS@@@@@@@Y
CLOG@DETECT.@@@@@Y
<CONTROL@SET>
EJECT@MODE@@@@@@@EJECT1
OPERATION@@@@@@@@SLAVE
NOTES:
œ The “VIDEO LOSS line does not appear if VIDEO
LOSS is set to “N” in the (GENERAL SET) menu.
œ The “CLOG DETECT.” line does not appear if “CLOG
DETECT.” is set to “N” in the (GENERAL SET) menu.
ALARM/SERIES REC SET menu
<ALARM/SERIES@REC@SET>
*ALARM@SET
@@MODE@@@@@@@@@@@Y1
@@SPEED@@@@@@@@@@8H
@@DURATION@@@@@@@20S
*1@SHOT@SET
@@FIELD@@@@@@@@@@1
@@INTERVAL@@@@@@@1M
*SERIES@REC@@@@@@N
*TAPE@END@OUT@@@@8:00
TAPE MANAGEMENT menu
<TAPE@MANAGEMENT>
*TAPE@MANAGEMENT@@@@N
*PROTECT@DAY@@@@@@@30
*REC@PASS@SET@@@@@@10
*GROUP@NO.SET@@@@@OFF
*OVERRIDE@@@@@@@@@@@N
TIMER SET menu
<TIMER@SET>
WEEK@@START@@STOP@@SPD
SUN@@@--:--@--:--@@---@N
MON@@@--:--@--:--@@---@N
TUE@@@--:--@--:--@@---@N
WED@@@--:--@--:--@@---@N
THU@@@--:--@--:--@@---@N
FRI@@@--:--@--:--@@---@N
SAT@@@--:--@--:--@@---@N
DAILY@--:--@--:--@@---@N
EXT@@@*****@*****@@---@N
HOLIDAY SET menu
<HOLIDAY@SET>
@@1@@-----@@@11@@-----
@@2@@-----@@@12@@-----
@@3@@-----@@@13@@-----
@@4@@-----@@@14@@-----
@@5@@-----@@@15@@-----
@@6@@-----@@@16@@-----
@@7@@-----@@@17@@-----
@@8@@-----@@@18@@-----
@@9@@-----@@@19@@-----
@10@@-----@@@20@@-----
OTHERS menu
<OTHERS>
*ALARM@LOG
*POWER@FAILURE/DEW
*TERMINAL@SET@@@@SET1
*RS-485@SET
@@STATUS@INFO.@@@Y
@@ALARM@INFO.@@@@Y
NOTE:
œ This is the display when the RS-485 interface board is
installed. The last three lines will not appear if this
board is not installed.
ALARM LOG menu
<ALARM@LOG>@@@@@@@@@000
@@@001@@@-----@--:--
@@@002@@@-----@--:--
@@@003@@@-----@--:--
@@@004@@@-----@--:--
@@@005@@@-----@--:--
@@@006@@@-----@--:--
@@@007@@@-----@--:--
@@@008@@@-----@--:--
@@@009@@@-----@--:--
@@@010@@@-----@--:--
POWER FAILURE/DEW/USED TIME menu
<POWER@FAILURE>
000@FAILURE@@-----@--:--
@@@@RECOVERY@-----@--:--
<DEW>
000@FAILURE@@-----@--:--
@@@@RECOVERY@-----@--:--
<USED@TIME>
@@VIDEO@@@@@@@@@00000H
@@POWER@@@@@@@@@00000H
NOTES:
œ Setting items are highlighted (appear in blue
characters) when they are selected.
œ Settings flash while they are being changed.
œ When a menu is displayed, recording will not be
possible.
œ During recording or playback the menus cannot be
displayed.
œ To reset the settings of a menu to their original
values, select the desired menu and then press the
MENU RESET button.
œ The USED TIME data in the (POWER
FAILURE/DEW/USED TIME) menu cannot be cleared
even when the MENU RESET button is pressed.
œ Press the MENU button to save any settings made
and switch menu screens. To display the (ALARM
LOG) menu or (POWER FAILURE/DEW/USED TIME)
menu, select the ALARM LOG or POWER
FAILURE/DEW” line in the (OTHERS) menu and then
press the ENTER button.
œ Press the CLEAR button while a setting item is
highlighted (appears in blue characters) to return to
the main menu. In the case of the (ALARM LOG)
menu or the (POWER FAILURE/DEW/USED TIME)
menu, to return to the (OTHERS) menu.
NB4QR/NA (SRT-4040 GB) Tue. Sept., 10/2002
English
11