Filter
Top Products
- 6 -
• Never cover the ventilation slots of the device while it is being used.
• Do not place any open sources of fire, like candles, on the device.
Injury hazard
• Keep children away from the connecting cable and the device. Children
frequently underestimate the dangers of electrical devices.
• Ensure that the device stands with a safe and secure positioning.
• Do not operate the device if it has sustained a fall or is damaged. Arrange for
the device to be checked and/or repaired by qualified technicians.
• Batteries/Cells can be fatal if swallowed. Store batteries out of the reach
of children. If a battery is swallowed, medical assistance must be sought
IMMEDIATELY.
• Also, store the packaging foils well away from children. There is a risk of
suffocation!
Danger! Laser radiation!
This device is fitted with a „Class 1 Laser“.
• Never open the device.
• Never attempt to repair the device.
• There is invisible laser radiation inside the device.
Do not expose yourself to the laser beam.
Note:
Some aggressive furniture finishes can have a destructive influence on the de-
vice's rubber feet. If necessary, place the device on a nonslip pad.
Thunderstorms!
Equipment connected to a power supply can be damaged during a thunder-
storm. You should therefore always pull the power plug from
the power socket when there is a storm.
Notice regarding electrical power surges (EFT /
electrical fast transient) and electrostatic discharges:
In a case of malfunction due to an electrical fast transient (power surge)
and/or electrostatic discharge, the device must be returned to default settings
in order to re-establish normal operation. Possibly the power supply must be
separated and then reconnected. The batteries (if present) must be removed
and then reinserted.
Notice regarding separation from mains-power
The POWER switch does not completely disconnect the device from the power
network. Additionally, the device consumes power when in standby-mode. To
completely separate the device from mains-power, the power plug MUST be re-
moved from the wall socket.
Information regarding the handling of batteries
The remote control is operated by batteries.
For the handling of batteries please observe the following:
Risk of explosion!
Do not throw batteries into a fire. Do not recharge the batteries.
• Never open batteries, never solder or weld batteries.
The risk of explosions and injuries exists!
• Regularly check the condition of the batteries. Leaking batteries can
cause damage to the device.
• If you do not intend to use the device for an extended period, remove the
batteries.
• In the event of the batteries leaking acids, wear protective gloves.
• Clean the battery compartment and the battery contacts with a dry cloth.
Attention!
No liability/warranty will be considered for damage to the DVD player cau-
sed by the effects of moisture, water penetration or overheating!
7. Remote control
7.1 Inserting the batteries
1.Open the battery compartment on the rear of the remote control.
2.Place the two supplied batteries type AAA (micro cells) into the battery
compartment. Make sure that the batteries are inserted in accordance
with the correct polarity.
3.Replace the battery compartment cover.
7.2 Using the remote control
In order to guarantee faultless operation when using the remote control…
• Always point the remote control, during use, directely at the DVD player
• Make sure that there are no obstructions between the remote control and
the DVD player that will hinder reception.
• When using the remote control place yourself not more than 5 metres
from the DVD player
otherwise interferences can occur during operation of the DVD player functions
with the remote control.
7.3 Replacing the batteries
If the operation of the DVD player via the remote control does not function
properly or does not function at all the batteries must be replaced
• Always renew all batteries in order to return the remote control to its
full performance ability.
8. Connecting the DVD Player to a television
After setting up the DVD player, you can now connect it to a television. The
DVD player can be connected to televisions which operate with the PAL and
NTSC standards.
If you want to use the DVD player on a television with the NTSC standard
you must change the video setting in the DVD players "OSD menu".
There PAL is set as the television standard at the factory.
On this topic see also chapter 10.3. "Video settings: Setting the
TV standard".
Depending on the televisions equipment there are different methods of
connecting the DVD player to it, these are explained as follows.
IB_KH6519_20_LB6 04.12.2008 14:41 Uhr Seite 6