Toshiba 19W330DG CRT Television User Manual


 
English - 2 -
Safety Precautions
This equipment has been designed and manufactured to meet international safety standards but, like any electrical
equipment, care must be taken to obtain the best results and for safety to be assured. Please read the points below for
your own safety. They are of a general nature, intended to help with all electronic consumer products and some points may
not apply to the goods you have just purchased.
Air Circulation
Leave more than 10cm clearance around the television to
allow adequate ventilation. This will prevent overheating
and possible damage to the television. Dusty places should
also be avoided.
Heat Damage
Damage may occur if the television is left in direct sunlight
or near a heater. Avoid places subject to extremely high
temperatures or humidity, or locations where the tempera-
ture is likely to fall below 5°C (41°F).
Mains Supply
IMPORTANT: The TV set is designed to operate on 12 V
DC. For this, an adaptor is used which gives 12 V
voltage. Connect this adaptor to a system that sup-
plies 230 V AC 50Hz.
WARNING: Only connect the adaptor supplied with
this product.
Important Note; before use, please check that the low
voltage DC rating on the adaptor corresponds to the
DC voltage rating on the back cover of the LCD TV. If
not the same or in doubt, please contact your Toshiba
dealer or a competent electrician.
DO ensure that the television is not standing on the mains
lead. DO NOT cut off the mains plug from this equipment,
this incorporates a special Radio Interference Filter, the
removal of which will impair its performance. It should only
be replaced by a correctly rated and approved type and the
fuse cover must be refitted. This set requires an earthed
supply. IF IN DOUBT PLEASE CONSULT A COMPETENT
ELECTRICIAN.
Do
DO read the operating instructions before you attempt to
use the equipment.
DO ensure that all electrical connections (including the mains
plug, extension leads and interconnections between pieces
of equipment) are properly made and in accordance with the
manufacturers’ instructions. Switch off and withdraw the
mains plug before making or changing connections.
DO consult your dealer if you are ever in doubt about the
installation, operation or safety of your equipment.
DO be careful with glass panels or doors on equipment.
Do not
DON’T remove any fixed cover as this may expose dan-
gerous voltages.
DON’T obstruct the ventilation openings of the equipment
with items such as newspapers, tablecloths, curtains, etc.
Overheating will cause damage and shorten the life of the
equipment.
DON’T allow electrical equipment to be exposed to dripping
or splashing or objects filled with liquids, such as vases, to
be placed on the equipment.
DON’T place hot objects or naked flame sources, such as
lighted candles or nightlights on, or close to equipment.
High temperatures can melt plastic and lead to fires.
DON’T use makeshift stands and NEVER fix legs with
wood screws. To ensure complete safety, always fit the
manufacturers’ approved stand, bracket or legs with the
fixings provided according to the instructions.
DON’T leave equipment switched on when it is unattended,
unless it is specifically stated that it is designed for unat-
tended operation or has a standby mode. Switch off by
withdrawing the plug, make sure your family know how to do
this. Special arrangements may need to be made for people
with disabilities.
DON’T continue to operate the equipment if you are in any
doubt about it working normally, or it is damaged in any way
- switch off, withdraw the mains plug and consult your
dealer.
WARNING - excessive sound pressure from earphones or
headphones can cause hearing loss.
ABOVE ALL - NEVER let anyone, especially children,
push or hit the screen, push anything into holes, slots
or any other openings in the case.
NEVER guess or take chances with electrical equip-
ment of any kind - it is better to be safe than sorry.
THE MAINS PLUG IS USED AS A DISCONNECTING DE-
VICE AND THEREFORE SHOULD BE READILY OPER-
ABLE.
WARNING - The power adaptor may become hot dur-
ing normal operation. This is not a malfunction. Please
make sure that the adaptor is not covered.