Filter
Top Products
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix Index
15
LIGHT
CT-90158
1 In the remote control code table (below and on the next page), find
the code for your device. If more than one code is listed, try each one
separately until you find one that works.
2 Set the Device Switch to the type of device you are programming the
remote control to operate—CBL/SAT (for a cable converter box or
satellite receiver), VCR (for a VCR or TV/VCR combo), or DVD
(for a DVD player or HTIB [home theater in a box]).
3 While holding down RECALL, press the Channel Number buttons
to enter the 3-digit code for your device.
4 To test the code, turn on the device, point the remote control at it,
and press POWER.
–If the correct code was entered, the device will turn off.
–If the device does not respond, repeat steps 1–4 using another code.
Note: After programming the TV remote control to operate your other device,
confirm that all necessary keys are operational. If some keys on the TV remote
control do not operate certain features on your other device, reprogram the
remote control using another code (if other codes are listed for your device).
If, after trying all listed codes, the necessary buttons do not operate your device,
use the device’s original remote control.
5 Remember to set the Device Switch back to “TV” to control the TV.
6 For future reference, write down the code(s) you used:
Programming the remote control to operate a cable converter box,
satellite receiver, VCR, DVD player, or HTIB (home theater in a box)
Your Toshiba TV remote control is preprogrammed to operate most Toshiba devices. To program your TV remote
control to operate a non-Toshiba device or a Toshiba device that it is not preprogrammed to operate, follow the steps
below. For details on using the remote control to operate the device, see page 17.
POWER
Channel
Numbers
}
RECALL
Device Switch
Note:
Each time you change the batteries, you must reprogram the remote control.
Some newer VCRs respond to either of two codes. These VCRs have a
switch labeled “VCR1/VCR2.” If your VCR has this kind of switch and does
not respond to the codes for your VCR brand, set the switch to the other
position (“VCR1” or “VCR2”) and reprogram the remote control.
DEVICE CODE DEVICE CODE
Cable converter box
ABC: 061, 062, 063, 082,
084, 087, 091, 092,
096, 098
Archer: 065, 092, 097, 099
Cableview: 064, 094
Century: 092
Citizen: 090, 092, 097
Contec: 083, 085, 086,
088, 093, 098
Diamond: 093
Eagle: 091
GE: 061, 062
Gemini: 069, 070, 094
General Instruments: 062,
089, 096
Hamlin: 093
Hitachi: 062, 095, 096
Jasco: 097
Jerrold: 062, 069, 071,
082, 086, 089, 091,
096
Magnavox: 072, 096
Memorex: 091, 092, 104
Multi Canal: 090
Novavision: 101
Panasonic: 081, 083, 085
Philco: 087
Philips: 066, 067, 068,
070, 072, 073, 074,
075, 091, 092
Pioneer: 076, 077
Proscan: 061, 062
Radio Shack: 092, 097,
099
RCA: 064, 081
Realistic: 065
Recoton: 102
Samsung: 077, 090
Scientific Atlanta: 063,
078, 079, 080, 088,
098, 101, 105
Sears: 095
Signature: 062
Signature 2000: 096
Sprucer: 081, 085
Starcom: 069, 082, 087,
096, 103, 104
Stargate: 069, 090
Sylvania: 095, 100
TeleView: 090
Texscan: 100
Tocom: 071, 084, 085
U. S. Electronics: 087,
096, 098
United Cable: 082
Universal: 065, 092, 097,
099, 102, 103
Wards: 096
Satellite receiver
Alphastar: 038, 059
Chaparral: 034
DISH Network: 057
Drake: 020, 040, 044, 046,
050, 053
Echostar: 018, 041, 051
Express Vu: 057
Fujitsu: 027
GE: 008, 009, 013
Remote control codes
In some cases you may not be able to operate your device with the TV remote control. Your other device may use a
code that is not recognized by the TV remote control. If this happens, you will need to use the remote control provided
with the device.