Filter
Top Products
15
Getting started
Programming channels automatically
- analog only -
First, use the Auto tuning function to preset all the active
channels in your area automatically. Then, arrange the preset
channels with the Manual tuning function so that you can tune
into only desired channels.
1 Press M, then press Y or Z to display the SET UP
menu.
2 Press V or U to select Auto tuning.
3 Press Q to display the Auto tuning menu.
4 Press Q to start the automatic search.
The search will begin for all available stations.
The slide bar will move along the line as the search
progresses.
If you make a mistake, simply repeat steps 1-4 to start
again from the beginning.
5 When the automatic search is completed, the TV will
automatically return to the first programme position.
6 Press V or U to view the programmed position.
Note:
When you preset the programme channel which sound of
broadcast transmission system adopts “M” system, the sound
system may not be tuned correctly if the radio waves transmit
badly. At that time, preset the channel by Manual tuning.
Manually setting channels in the channel
memory
- analog only -
Use the Manual tuning operation if desired channels cannot be
preset with the Auto tuning or if you would like to preset
channels to specific position numbers one by one.
1 From the SET UP menu, press V or U to select Manual
tuning.
2 Press Q to display the Manual tuning menu.
Press V or U to select the programme position you want
to arrange.
3 Press Q to display the breakdown menu.
Press Y or Z to select an item, then press V or U to
select the item as shown below.
A. Programme position selection
B. Sound system (- page 42)
C. Colour system (- page 42)
A : Automatic (factory set), P : PAL, S : SECAM
N4 : NTSC 4.43 (MHz), N3 : NTSC 3.58 (MHz)
If the colour of a certain channel is abnormal, the
automatic colour system selection (A) may have
malfunctioned, or sound system selection is wrong. In
such a case, select another colour and/or sound system
(- page 42).
D. Programme position skip selection
Press V or
U to turn the programme position skip
option on “8” or off “(”.
The programme position will then be skipped when
you select channels with PU or P u.
The “8” mark will appear beside a programme
position number when you use the Number button on
the remote control.
E. Channel search operation
Press U to search up the band or V to search down the
band.
Press V or U repeatedly until your desired channel is
displayed.
When a station/satellite is found, it will be displayed.
NEVER PRESS ANY OTHER BUTTONS WHILE
THE SET IS TUNING.
F. Auto Fine Tuning
Press V or U to t
urn the Auto Fine Tuning option on
“9” or off “0”.
The Auto Fine Tuning function automatically corrects
slight fluctuations when receiving signals.
Manual Fine Tuning
While the Auto Fine Tuning turn off “0”, press V or
U so that the better picture and sound are obtained.
G. Label
Station labels appear under the programme position
display each time you turn on the TV, select a channel,
or press k.
To change or create station labels:
1) Press V or U repeatedly to select a character for
the first space, then press Z.
2) Repeat step 1) to enter the rest of the characters. If
you would like a blank space in the label name, you
must choose a blank space from the list of
characters.
Press Q to store your settings.
Manual tuning
OK
AV connection
OK
Picture position
OK
Auto tuning
OK
Language
SET UP
MENU
Back Watch TV
EXIT
English
MENU
Back Watch TV
EXIT
Auto tuning
EXIT for no change.
Press OK key to start.
!
Searching
Stop
Pos :2
Auto tuning
EXIT
5
4
3
2
1
MENU
Back Watch TV
EXIT
6
OK
Manual tuning
Prog. Label
Select
Sort
ACE
BDF
G
MENU
Back Watch TV
EXIT
OK
Manual tuning
Store
1
B/G
Programme
A
*(blank space)