Filter
Top Products
TELEVISION
888 14159
Acer 11339, 14143
Admiral 10093, 10463
Advent 10761, 11570
Affinity 13717, 13716, 13870, 13577
Aiwa 11362
Akai 11675, 10702, 11688, 11207,
11385, 11692, 11935, 12232,
10765
America Action 10180
Anam 10180
AOC 11589, 13720, 11365, 12014,
12087, 11590, 12479, 13707
Aomni 11623
Apex Digital 10765, 12397, 10879, 10748,
11217, 10890
Ario 12397
Astar 11738
Asus 13340
Atvio 13636
Audiovox 11865, 12413, 11951, 10846,
10180, 11564, 11868, 10802,
11276, 11766, 11769, 12121,
11937, 13065, 10451, 12513
Aumark 10060
Auria 12087, 12014, 12277
Aventura 10171
Axion 11937
BenQ 11032, 11315
Bradford 10180
Broksonic 10463, 11935, 11938, 11892
Celera 10765
Champion 11362
Changhong 10765
Cineon 13951
Citizen 10060, 11669, 11935
Clarion 10180
Programming codes
Claris 13807
Coby 13478, 13627, 12315, 12344,
12306, 12314, 12345, 11634,
12338, 12326, 12340, 13629,
12350, 11538, 12347, 12348,
13202, 12560, 13646
Commercial
Solutions
11447
Contec 10180
Contex 14053
Craig 10180, 13423
Crown 10180
Curtis 13577, 12855, 13121, 12466,
12352, 13895, 12397, 11326,
13636, 11314, 13382, 14035
Curtis Mathes 10060, 10451, 10702, 11661,
10093, 11959
CXC 10180
Cytron 11326
Daewoo 11661, 10451, 10661, 11909
Dell 11264, 11080
Diamond
Vision
11996, 11997
Digistar 11565
Digital Lifestyles 11765
Digitrex 14207
Disney 11892, 11665
Dukane 11398
Dumont 10017
Durabrand 10463, 10171, 11570, 11665,
10180, 11034
Dynex 12049, 12184
Eiki 10735
Electrograph 11755, 11623
Electrohome 10463, 11570, 11670
Electron 12466, 12855
Elektra 10017, 11661
Element 13559, 11687, 12183, 12964,
11886
Elite 13867
Emerson 11864, 11394, 11963, 10171,
10463, 11886, 10180, 13559,
11661, 13623, 11665, 12183,
10451, 11909, 11997
Turn off keypad backlighting
By default, your remote control is set with the backlight on. Here’s how you can
turn it OFF or back ON again.
Step 1:
Press the AT&T mode key.
Step 2:
Enter programming mode – Press and hold the OK and
MENU keys simultaneously for three seconds until all four
mode keys flash red twice and you hear two short beeps to
confirm you are in programming mode.
Step 3:
Enter 9 7 2 – Using the numeric keypad on the remote, enter 9 7 2. The AT&T
mode key will flash red four times and you will hear four short beeps to indicate
that backlighting has been disabled.
If you repeat this process, the backlight will be re-enabled and the AT&T mode
key will flash red twice and you will hear two short beeps.
NOTE: Even with backlighting disabled, every press of the
BACKLIGHT key will turn the backlight on for five seconds.
Program Home ID code
Your Point Anywhere RF Remote Control and the USB converter were paired at
the factory. If you are experiencing RF interference or poor performance, you may
want to change your Home ID. To create a new Home ID, you may use any 4-digit
code from 0000 to 9999. To change the Home ID, follow the steps below.
Step 1:
USB converter pairing key – Press and hold the pairing key on the
USB converter until the blue power LED turns off. The USB converter
is now ready to be programmed.
NOTE: The USB converter will remain in programming mode for two
minutes to receive the Home ID command from the Point Anywhere
RF Remote Control. If the blue LED light turns ON, the USB converter
timed out and you must start over.
Step 2:
Select mode – Press the AT&T mode key to start the pairing process.
9