Filter
Top Products
OPERATOR PROGRAMMING INSTRUCTIONS
9
TRUNK RELEASE AND SLIDING VAN DOOR RELEASE (+)
Locate the trunk release or sliding van door release wire
coming from the back of the release switch. To determine
if your release is tripped by a (+) positive or a (-)
negative (most trunk release or van door release switches
are (+) positive). Press the “trunk” or “sliding door”
button, if the RED light glows bright, you have a (+)
positive release. If the GREEN light glows bright you have
a (-) negative release.
If your release is a (-) negative an
optional part #775 is required. Connect the WHITE WITH
RED STRIPE wire to the WHITE wire of the optional relay.
Attach the BLACK wire and the BLUE wire to chassis ground
and attach the YELLOW wire to the release output wire on
the vehicle. Please use figures above for correct connections.
If your release wire is a (+) positive, connect the WHITE
with RED stripe wire from the 16-pin harness to the release
wire in the vehicle’s harness.
For more detailed information, visit www.bulldogsecurity.com
or contact Technical Support at 800-878-8007.
AUXILIARY INPUT (-)
If you wish to use this starter with an aftermarket alarm,
connect the BLUE wire from the 16-pin harness to the
second or third channel (-) output of your existing alarm.
When the output is activated, a (-) signal will be supplied
to the remote starter which will start the vehicle.
Adding Additional Remotes
Press and hold brake. Next, press and hold Button #1 on the working remote until the parking lights
flash once, release. Press and release Button #4 on the new remote. The parking lights will flash three
(3) times confirming that the new remote was learned.
Cold Start On and Off (Degree Select)
Press and hold brake. Next, press and hold Button #2 until the parking lights flash twice, release,
press and hold Button #2. Each parking light flash is a progression in degrees. Flash #1 is -40ºF, flash
#2 is -30ºF, flash #3 is -20ºF, flash #4 is -10ºF, flash #5 is 0ºF, flash #6 is +10ºF, flash #7 is +20ºF.
Two rapid flash parking light flashes is Cold Start Off. Release the brake, the parking lights will
flash three (3) times. NOTE: Factory setting is OFF.
Door Lock Pulse Length (Long) (For European type door locks)
Press and hold brake. Next, press and hold Button #3, the parking lights will flash three (3) times,
release, press and release Button #1. The parking lights will flash once, the door lock pulse length
will be 3.5 seconds. Release the brake, the parking lights will flash three (3) times.
Door Lock Pulse Length (Short)
Press and hold brake. Next, press and hold Button #3, the parking lights will flash three (3) times,
release, press and release Button #1. The parking lights will flash twice, the door lock pulse length
will be 0.7 seconds. Release the brake, the parking lights will flash three (3) times. NOTE: Factory
setting is SHORT pulse length.
Tach Mode - ON
Press and hold the brake pedal. Press and hold Button #3 until the parking lights flash three (3) times. Release. Press
and release Button #4, the parking lights will flash twice. Release the brake, the parking lights will flash three (3)
times. The unit is now programmed for Tach Mode.
NOTE: Factory setting is Tachless Start ON.
Tachless Mode - ON
Press and hold the brake pedal. Press and hold Button #3 until the parking lights flash three (3) times, release, press
and release Button #4, the parking lights will flash once. Release the brake, the parking lights will flash three (3)
times. The unit is now programmed for Tachless Mode.
Tach Learn
To program your unit to Learn your tach signal. Press and hold the brake pedal, now press and hold Button #2 until the
parking lights flash twice. Release Button #2. Turn your ignition key to the RUN or ON position while still holding the
brake, press and hold Button #4 until the vehicle starts. After the engine starts, release Button #4 to disengage the
starter. Release the brake and turn the ignition OFF. After the Tach Learn is complete, the unit will flash the parking
lights once to show that the Tach Learn is now programmed. Now try the remote starter, to be sure there is no over crank
and the unit does crank long enough.
NEGATIVE TRUNK/
SLIDING DOOR RELEASE ONLY
Optional part #775 required.
TO FACTORY TRUNK/SLIDING DOOR WIRE WIRE
THE RED WIRE IS NOT
USED, TAPE OFF.
87a
WHITE/RED
FROM REMOTE
STARTER
YELLOW
BLACKWHITE
BLUE
RED
Ground