Filter
Top Products
6
Introduction Introduction
ENGLISH
ENGLISH
Introduction Connections Playback Function Setup Others
Keep in mind the following when using the remote control:
• Make sure that there are no obstacles between the remote
control and infrared sensor window on the unit.
• Remote operation may become unreliable if strong sunlight or
fluorescent light is shining on infrared sensor window of the
unit.
• Remote control for different devices can interfere with each
other. Avoid using remote control for other equipment located
close to the unit.
• Replace the batteries when you notice a fall off in the operating
range of the remote control.
• The maximum operable ranges from the unit are as follows.
If you have other DENON’s DVD players around this unit, this unit
reacts to the commands you made for DVD players through its
remote control. To avoid this situation, you can set this unit not
react to other DENON’s DVD player's remote control.
1) In stop mode, press [SETUP].
2) Press [7],[8],[9],[2].
3) Press [SETUP].
• “Only Attached Remocon” will be displayed on the upper
right corner of the screen and this unit only react to the
commands from this unit's remote control.
• To set back to default, press [7],[8],[9],[1] at step 2). “Normal
Remocon” will be displayed on the upper right corner of the
screen and this unit react to both the commands from this unit's
remote control and the other DENON’s DVD players' remote
control.
To avoid the other DENON’s BD players responding the remote
signal of this unit, you can change the signal code of the remote
control. If the signal code of the remote control does not match to
the signal code of the unit, you cannot control the unit with the
remote control.
Ⅵ Change the signal code of the unit
1) In stop mode, press [SETUP].
2) Use [Y / Z] to select , then press [ENTER].
3) Use [Y / Z] to select , then press [ENTER].
4) Use [U / V] to select “Remote Control Setting”.
5) Press [ENTER] to select “DENON1” or “DENON2”.
6) Press [SETUP] to exit.
• At this point the new signal code of the unit is effective. Please
change the signal code of the remote control to match to the
signal code of the unit with following procedure.
Ⅵ Change the signal code of the remote control
Set to “DENON1”:
Press and hold [RETURN], and press [3], [2], [1].
Set to “DENON2”:
Press and hold [RETURN], and press [1], [2], [3].
• If the signal code does not match, the signal code of the main
unit will be displayed on the front panel display.
• The default setting and the setting after you change the
batteries is “DENON1”.
• If the code setting on the unit is “DENON1”, and the setting on
the remote control is “DENON2”, “PLAYER 1” is shown on the
front panel display.
About the Remote Control
Loading the Batteries
A Open the battery
compartment cover.
B Insert two “AA” (R6)
batteries, with each one
oriented correctly.
C Close the cover.
Cautions on Batteries
• Use “AA” (R6) batteries in this remote control.
• Replace the batteries with new ones approximately once a
year, though this depends on the frequency with which the
remote control is used.
• If the remote control does not operate within a close
proximity of the main unit, replace the batteries with new
ones, even if less than a year has passed.
• The included batteries serve only for verifying operation.
Replace them with new batteries as soon as possible.
• When inserting the batteries, be careful to do so in the
proper direction, following the and marks in the remote
control’s battery compartment.
• To prevent damage or battery fluid leakage:
- Do not mix a new battery with an old one.
- Do not mix two different types of batteries such as alkaline
and manganese.
- Do not short-circuit, disassemble, heat or dispose of
batteries in flames.
• Remove the batteries when not planning to use the remote
control for a long period of time.
• If the batteries should leak, carefully wipe off the fluid from
the inside of the battery compartment, then insert new
batteries.
Using a Remote Control
- Line of sight: approx. 23 feet (7m)
- Either side of the center: approx. 23 feet (7m) within 30°
Setting this Unit not React to Other DENON’s DVD
Player’s Remote Control
Note
• The setting remains after you turn the unit to the standby
mode or unplug the AC cord.
• If you try to operate this unit with the other DENON’s DVD
players' remote control, some of the operation may not be
available depending on the manufactured year or type of the
remote control.
ON / STANDBY
SD CARD
30°30°
23 feet (7m) 30° 23 feet (7m) 23 feet (7m) 30°
Changing the Signal Code of a Remote Control
Power Saving
On
Remote Control Setting
DENON1
HDMI CEC On
Media Select Disc
Network Connection Enable(Easy)
Network Update
Others
E5KA0UD_EN.book Page 6 Tuesday, April 28, 2009 11:15 AM