Filter
Top Products
t When “IEEE1394” is selected:
OFF (Factory default)
Digital audio signals are not output from the IEEE1394
terminal.
ON
B
When “ON” is selected:
This will lead to the “AUTO PLAY”, and “AUDIO
FORMAT” setting screens. Select the item to be set
using the (
•
,
ª
) cursor buttons and press the ENTER
button.
B
Auto Play
Set this when automatically playing this unit from
another device, under circumstances in which this unit
is used in conjunction with a DENON device that
supports IEEE1394.
B
Audio Format
Set this format of audio signals from IEEE1394
connector.
B
Auto Play Setting Method
OFF (Factory default)
Set this when you do not wish to control the operation
of this unit from another device.
ON
Set this when you wish to control the operation of this
unit from another device.
B
Audio Format Setting Method
FORMAT 1 (Factory default)
Set this when you conjunction with a DENON device.
FORMAT 2
This is a mode for future system expansion.
IEEE1394 indicator
When “IEEE1394” set to “ON”, this indicator lights as
bellow.
flashing. . . . . . . . self check of IEEE1394
connections.
light. . . . . . . . . . . IEEE1394 connection is OK.
slow flashing. . . . IEEE1394 connection is NG.
(Loop connection) confirm the
connection.
fast flashing . . . . IEEE1394 connection is NG.
confirm the connection.
21
ENGLISH
3
Remote control unit
ENTER
Remote control unit
AUD IO SETUP
SELECT: DECISION:ENTER BUTTON
AUD IO CHANNEL
DI G I TAL OUT
LPCM(44.1kHz/48kHz)
BASS ENHANCER
OFF
IEEE1394
DENON LINK
EXIT SETUP
SOURCE D I RECT
ON
IEEE1 394 SETUP
IEEE1 394 SETUP
AUTO PL AY
AUDI O F ORMAT
OFF
F ORMAT 1
SELECT: DECISION:ENTER BUTTON
3
y When “SOURCE DIRECT ” is selected:
OFF (Factory default)
Please set to OFF when performing speaker settings or
setting the delay time and playing back.
ON
Set to ON when playing back without performing the
processing of speaker settings. Performing this setting
will result in the setting of the DTS recommended all-
channel, full bandwidth playback. (Note that the volume
of the sub woofer will increase by 5 dB, and there will be
an increase of 15 dB with a Super Audio CD.) This is also
set when playing back a 6-channel source of DVD audio
that has been recorded with all channels and full
bandwidth. When set to “OFF”, the speaker size will be
set to “Large” for all speakers and the sub woofer will
be set to “Yes”. When playing back software such as
this, perform the analog connections according to the
software instruction manual.
u When “BASS ENHANCER” is selected:
OFF (Factory default)
No sound is produced from the subwoofer.
ON
Sound is produced from the subwoofer.
In the case, set the subwoofer to “YES” at the speaker
settings.
✽
This works only with analog audio output.
Remote control unit
ENTER
Remote control unit
AUD IO SETUP
SELECT: DECISION:ENTER BUTTON
AUD IO CHANNEL
DI G I TAL OUT
LPCM(44.1kHz/48kHz)
BASS ENHANCER
ON
OFF
IEEE1394
DENON LINK
EXIT SETUP
SOURCE D I RECT
AUD IO SETUP
SELECT: DECISION:ENTER BUTTON
AUD IO CHANNEL
DI G I TAL OUT
LPCM(44.1kHz/48kHz)
BASS ENHANCER
ON
OFF
IEEE1394
DENON LINK
EXIT SETUP
SOURCE D I RECT
✽ To exit the setup mode
Use the ª cursor button to select “EXIT SETUP”, then press the ENTER button. It is also possible to quit
by pressing the SETUP button on the remote control unit.
IEEE 1394