Filter
Top Products
29
Recording
EN
7 Enter the time to start and to end
using [Cursor U / D], then press
[Cursor P].
8 Select the channel number to record
using [Cursor U / D], then press
[Cursor P].
To record from external input, select “AV1,” “AV2”
or “AV3.”
9 Select the recording media (“DVD” or
“VCR”) using [Cursor U / D], then
press [Cursor P].
10
Select the recording speed using
[Cursor U / D], then press
[Cursor P].
Refer to “Recording speed” on page 22 for DVD or
page 63 for VCR.
11
Select PDC “ON” or “OFF” using
[Cursor U / D]
(See page 30).
12
Press [ENTER] when all information
required is entered.
Your programme setting is stored.
• To set another programme, repeat steps 5 to 11.
• To exit, press [SETUP] or [TIMER PROG.].
• If the recording times of two or more
programmes overlap, “Overlap” and overlapped
programme numbers are displayed. (See page
29 and 31.)
13
Press [T-SET].
The icon will appear on the front panel display
and the unit enters to the timer-standby mode.
Note
• If you have not set the clock, the clock setting
window will appear after step 4. Continue from step
4 in “Manual Clock Setting” on page 20 before
programming the timer.
•Press [Cursor L / P] to move the cursor in the timer
programming menu.
• If a basic recording or one-touch timer recording is
in progress on one component (e.g. VCR) and the
timer recording set for the other component (e.g.
DVD) is about to begin, the unit automatically
switches to the programmed channel for timer
recording 2 minutes before the programmed starting
time, and the recording in progress (for VCR) will be
cancelled UNLESS their recording channels are the
same. If their recording channels are the same, the
timer recording will start without cancelling the
recording currently in progress. In this case, the
recording of the same channel will be made on both
DVD and VCR.
• Cancel the timer-standby mode by pressing [T-SET]
before operation for either DVD or VCR. When
finished operating, press [T-SET] to resume the
timer-standby mode.
If PDC is “ON”:
• In the timer-standby mode, you can neither turn on
the power nor use the component (VCR or DVD)
which is not currently timer-programmed.
If PDC is “OFF”:
• In the timer-standby mode, you can turn on the
power and use the component (VCR or DVD) which
is not currently timer-programmed.
Checking, cancelling, or correcting
the timer programming information
In the following example, No. 5 timer programming
overlaps on No. 1 and No. 6 timer programmes. In
such a case, you should correct the programme time
to clear the overlap.
1 Press [T-SET] so that the icon
disappears from the front panel
display.
2 Press [TIMER PROG.].
Timer programming list will appear.
3 Check the information on the list you
will need.
4 To clear the timer programming,
select the desired programme using
[Cursor U / D], then press [CLEAR].
To correct the timer programming
1)Select the desired programme using
[Cursor U / D], then press [ENTER].
2)Correct the timer programming using
[Cursor U / D / L / P].
3)Press [ENTER] again.
Timer Programming
1. 01/01 12:00 13:00 P01 DVD 1H
2.
- - -
3.
- - -
4.
- - -
5.
- - -
6.
- - -
7
ON
Date Start End CH Speed
PDC
DVD
VCR
VCR DVD
Timer Programming
1. 01/01 12:00 13:00 AV3 DVD 1H ON
2.
- - -
3.
- - -
4.
- - -
6. 01/01 13:45 21:00 P12 DVD 10H OFF
7.
- - -
8.
- - -
Overlap
No.1 6
01/01 12:30 14:00 P02 VCR SP OFF
Date Start End CH Speed
PDC
DVD
VCR
VCR DVD
5.
DRV_B2737_B2734.book Page 29 Thursday, March 31, 2005 10:04 PM