Filter
Top Products
—21—
Ⅵ AV COMPU-LINK — ON/OFF
The REMOTE PAUSE/AV COMPULINK terminal on the rear panel
can be used as either the REMOTE PAUSE terminal or the AV
COMPULINK terminal.
● When this function is set to “ON”, you can use this terminal as
the AV COMPULINK terminal. By connecting other JVC’s AV
COMPULINK components, including amplifiers (or receivers)
and televisions, one touch control of the audio and video
components linked via their AV COMPULINK connectors
becomes possible.
● When this function is set to “OFF”, you can use this terminal as
the REMOTE PAUSE terminal. If your JVC camcorder is
equipped with the Master Edit Control, you can control the VCR
from the camcorder. Connect the mini-plug cable (not supplied
with this VCR) between the REMOTE PAUSE terminal and the
EDIT connector on the camcorder.
NOTE:
Refer to the other components’ instruction manuals for connection
and its operations.
Ⅵ FRONT AUX INPUT — VIDEO/S-VIDEO
You have to select which terminal — either VIDEO (composite) or
S VIDEO (Y/C separate signals) to use as the video input terminal
on the front panel.
Make sure to select the correct terminal; otherwise, you may fail
in recording (editing) on this VCR.
Ⅵ REAR AUX INPUT — VIDEO/S-VIDEO
You have to select which terminal — either VIDEO (composite) or
S VIDEO (Y/C separate signals) to use as the video input terminal
on the rear panel.
Make sure you select the correct terminal; otherwise, you may fail
in recording (editing) on this VCR.
Satellite Auto Recording
You can automatically record a satellite program which is timer-
programed on your DBS receiver.
A Connect a DBS receiver to the AUDIO/VIDEO IN or S VIDEO IN
connectors* on the rear panel. You can also connect the cable
box if it has a timer.
* To use these connectors, you have to select which one to use.
(
੬ See above, “REAR AUX INPUT”.)
B Set timer program on DBS receiver using its instruction
manual.
C Load a cassette with the record safety tab intact.
D Press SP/EP (p) to set the tape speed. The selected tape
speed will appear on the TV screen.
E Press REC LINK for more than 2 seconds. The VCR turns off
automatically and enters the Satellite Auto Recording standby
mode and the REC LINK lamp lights. When the DBS receiver
outputs a signal, the VCR starts recording and the REC LINK
lamp blinks. The VCR stops recording and powers off when the
DBS receiver stops outputting a signal.
NOTES:
● Be sure not to turn on the DBS receiver before the program starts
broadcasting; otherwise, the VCR will start recording when the
DBS receiver is turned on.
● To disengage the Satellite Auto Recording standby mode, press
REC LINK (the REC LINK lamp goes off).
● Depending on the type of DBS receiver, Satellite Auto Recording
may not be compatible.
Child Lock
You can disable the VCR operations. While
the VCR is turned on, press and hold
POWER on the Remote
for more than
10 seconds. The VCR turns off, “CL”
appears for about 5 seconds on the display
panel.
To release the child lock, press and hold POWER on the Remote
until the VCR turns on.
NOTES:
● Pressing TIMER (#) during timer recording, unplugging the AC
power cord or a power outage also releases the child lock.
● Even if the child lock function is in use, it is possible to engage
and disengage the timer mode with TIMER (#) on the Remote.
Keep the Remote out of the children’s reach.
● Timer recording programs will be performed even if the child
lock function is activated.
JLIP ID Number Setting
The JLIP (Joint Level Interface Protocol) terminal is used to connect
the VCR to a personal computer or similar device. By connecting
through the JLIP terminals, you can control the VCR during editing
and certain other operations, from the connected personal
computer or similar device.
When connecting this VCR to another device using the JLIP
terminals, each device must have a different JLIP ID number.
The JLIP ID number of this VCR is preset to “1” when shipped
from the factory. You can change this number to any other number
between 1 to 99.
NOTE:
For further details on the JLIP system or devices, consult your
nearest JVC dealer.
A Access Main Menu screen, then Initial Set screen
Press MENU on the Remote. Press rt to move the highlight bar
(arrow) to “INITIAL SET”, then press OK or
e.
B Access JLIP ID Number Set screen
Press rt to move the highlight bar
(arrow) to “JLIP ID NO. SET”, then press
OK or
e.
C Set JLIP ID number
Press the appropriate Number keys on the
Remote to enter the desired ID number,
then press OK.
Press MENU to return to normal screen.
● Turn on the VCR and TV, and select the VCR channel (or AV
mode).
● Set the VCR/TV/CABLE/DBS selector on the Remote to
“VCR”.
● Turn on the VCR and TV, and select the VCR channel (or AV
mode).
● Set the VCR/TV/CABLE/DBS selector on the Remote to
“VCR”.
● Turn on the VCR and TV, and select the VCR channel (or AV
mode).
● Set the VCR/TV/CABLE/DBS selector on the Remote to
“VCR”.
Child lock
indicator
HR-S9911U-EN.fm Page 21 Friday, April 26, 2002 11:37 AM