Filter
Top Products
—23—
C
Change code for VCR
Press any key on the Remote. The VCR now responds to B code
control signals.
●
To set the Remote and the VCR to transmit and respond to A
code control signals, repeat above procedure as shown above
except press the Number key “1” in step
B
of
1
11
1
.
To control two VCRs with the same Remote
You can control two JVC VCRs by switching the remote control
code for the Remote between A and B (
੬
step
A
AA
A
), keeping two
VCRs to different control codes.
●
To change only the remote control code for the Remote, DO
NOT perform steps
B
BB
B and C
CC
C.
Editing from Camcorder
You can use a camcorder as the playback unit and your VCR as the
recording VCR. Refer also to the camcorder’s instruction manual
for connection and its operations.
A
Make connections
●
When the JVC camcorder is equipped with the Master Edit
Control, you can control the VCR from the camcorder. Connect
the mini-plug cable (not supplied with this VCR) as illustrated.
●
If camcorder is monaural, connect the audio output connector
on the camcorder to the left audio input connector on this VCR.
B
Load cassettes
Insert the playback cassette into the camcorder and the cassette to
be recorded on into this VCR.
C
Select input location on this VCR
Select the correct external input location on this VCR.
Select “L-1” —when connecting the camcorder to the audio/video
(or S-video) input connectors on the rear panel.
Select “F-1” —when connecting the camcorder to the audio/video
(or S-video) input connectors on the front panel.
On the VCR
Press CH+/– or push the ADVANCED JOG dial, then turn it to the
left or right until “L-1” or “F-1” appears on the display panel.
On the Remote
Press AUX and/or CH+/– until “L-1” or “F-1” appears on the
display panel.
D
Select video input connector
Select the appropriate mode depending on the connector being
used (
੬
pg. 21).
When using S-VIDEO input connector on the front panel, set
“FRONT AUX INPUT” to “S-VIDEO”.
When using S-VIDEO IN connector on the rear panel, set “REAR
AUX INPUT” to “S-VIDEO”.
When using VIDEO input connector on the front panel, set
“FRONT AUX INPUT” to “VIDEO”.
When using VIDEO IN connector on the rear panel, set “REAR
AUX INPUT” to “VIDEO”.
E
Select edit mode
Set “PICTURE CONTROL” to “EDIT” (
੬
pg. 20).
F
Set AV COMPU-LINK mode
If your JVC camcorder is equipped with a Master Edit Control, set
“AV COMPU-LINK” to “OFF” (
੬
pg. 21). The REMOTE PAUSE/
AV COMPULINK connector works as a Remote Pause connector.
G
Start playback
Set the camcorder to its play mode.
NOTE:
If the camcorder is equipped with a superimpose/OSD disable
feature, set it to “OFF” before starting playback.
H
Start recording
On the VCR
Press REC (
7
).
On the Remote
While holding REC (
7
), press PLAY (
4
).
●
If you are using a Master Edit Control-equipped JVC camcorder,
recording starts automatically on this VCR. (Refer to camcorder’s
instruction manual.)
NOTE:
Be sure to select “AUTO” for “PICTURE CONTROL” (or “NORM”
when “VIDEO CALIBRATION” is set to “OFF”) after you finish
dubbing the tapes. (
੬
pg. 20)
Editing
Various connection for editing tapes
The following three methods can be used for editing tapes.
●
VHS to S-VHS editing (VIDEO-VIDEO connection):
Although the picture quality is inherently limited by the original
VHS quality, the edited tape has better picture quality than
those made by VHS-to-VHS editing.
●
S-VHS to VHS editing (VIDEO-VIDEO connection):
Since the original source is recorded in S-VHS mode, the edited
tape has better picture quality than those made by VHS-to-VHS
editing.
●
S-VHS to S-VHS (S-VIDEO connection):
Original picture quality of S-VHS made can be duplicated with
minimal picture degradation. This is the best editing method
you can use on S-VHS VCRs.
To S-video output
This VCR (for recording)
Camcorder
(for playback)
S-video cable
(supplied)
To AUDIO/VIDEO
input
To S-VIDEO input
Audio/video cable
(supplied)
To audio/video
output
To EDIT
To rear panel
REMOTE PAUSE/
AV COMPULINK
Mini-plug cable
(not supplied)
(JVC camcorder only)
HR-S9911U-EN.fm Page 23 Monday, April 22, 2002 1:34 PM