Filter
Top Products
Important Information
Precautions
Please read this manual carefully before using your Mitsubishi
plasma monitor and keep the manual handy for future
reference.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER. NO
USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This symbol warns the user that uninsulated
voltage within the unit may have sufficient
magnitude to cause electric shock. Therefore,
it is dangerous to make any kind of contact
with any part inside of this unit.
This symbol alerts the user that important
literature concerning the operation and
maintenance of this unit has been included.
Therefore, it should be read carefully in order
to avoid any problems.
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE
THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD
RECEPTACLE OR OTHER OUTLETS, UNLESS THE
PRONGS CAN BE FULLY INSERTED. REFRAIN FROM
OPENING THE CABINET AS THERE ARE HIGH-VOLTAGE
COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Warning
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference when the equipment is
operated in a commercial environment. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instruction
manual, may cause harmful interference to
radio communications. Operation of this
equipment in a residential area is likely to
cause harmful interference in which case the
user will be
required to correct the
interference at his own expense.
Warnings and Safety Precautions
The Mitsubishi plasma monitor is designed and
manufactured to provide long, trouble-free service.
No maintenance other than cleaning is required. Use
a soft dry cloth to clean the panel. Never use
solvents such as alcohol or thinner to clean the panel
surface.
The plasma display panel consists of fine picture
elements (cells). Although Mitsubishi produces the
plasma display panels with more than 99.99 percent
active cells, there may be some cells that do not
produce light or remain lit.
For operating safety and to avoid damage to the unit,
please read and observe the following instructions.
To avoid shock and fire hazards:
1. Provide adequate space for ventilation to avoid internal
heat build-up. Do not cover rear vents or install the unit
in a closed cabinet or shelves.
The unit is equipped with cooling fans. If you install the
unit in an enclosure, make sure there is adequate space at
the top of the unit to allow hot air to rise and escape. If
the monitor becomes too hot, the overheat protector will
be activated and the monitor will be turned off. If this
happens, turn off the power to the monitor and unplug
the power cord. If the room where the monitor is installed
is particularly hot, move the monitor to a cooler location,
and wait for the monitor to cool for 60 minutes. If the
problem persists, contact your Mitsubishi dealer for
service.
2. Do not use the power cord polarized plug with extension
cords or outlets unless the prongs can be completely
inserted.
3. Do not expose the unit to water or moisture.
4. Avoid damage to the power cord, and do not attempt to
modify the power cord.
5. Unplug the unit during electrical storms or if the unit will
not be used over a long period.
6. Do not open the cabinet which has potentially dangerous
high voltage components inside. If the unit is damaged in
this way the warranty will be void. Moreover, there is a
serious risk of electric shock.
7. Do not attempt to service or repair the unit. Mitsubishi is
not liable for any bodily harm or damage caused if
unqualified persons attempt service or open the back
cover. Refer all service to authorized Mitsubishi Service
Centers.
Caution
PD-5030 and PD-6130 are for use with the following
optional accessories. Use with other optional accessories
is capable of resulting in instability causing possible injury.
Manufacturer’s name: MITSUBISHI DIGITAL
ELECTRONICS AMERICA, INC
Stand: MB-5010/MB-5030 for PD-5030
MB-6130 for PD-6130
Please contact MITSUBISHI DIGITAL ELECTRONICS
AMERICA, INC for approved optional accessories.