Mitsubishi Electronics WD-60735 Flat Panel Television User Manual


 
32 4. TV Operation and Features
4. TV Operation and Features 33
Viewing Camera Files
JPEG Photos and the USB Photo Port
Connect your
1.
USB card
reader or
USB drive to
the TV’s USB
Photo port.
The USB
Photo menu
displays
while files are being read. Wait until you see the
completion message on screen before continuing.
Note:
Some manufacturers’ devices may be incompat-
ible with the TV. If the TV is unable to display your
photos, you can:
• Transfer
files to a different USB device.
• Usethecamera’scompositevideooutputas
described later in this chapter.
USB Photo menu
Refer to the table below for use of the
2.
USB Photo
menu after files have been read.
Optional:
3.
Connect an audio device to the AUDIO L and
R stereo jacks to play sound while viewing pictures
JPEG Thumbnail Menu
Use these keys while viewing JPEG thumbnail images:
Keys for the JPEG Thumbnail Menu
Move the highlight from image to image.
F
ORMA
T Rotate the thumbnail clockwise in 90˚
increments
or
ENTER
Play the slide show starting with the high-
lighted thumbnail.
Highlight the last thumbnail on the current
page.
Highlight the first thumbnail on the current
page.
CH/PAGE
/
Display the next or previous page of
thumbnails.
EXIT
Close the Thumbnail menu and display
the USB Photo menu.
MENU
Close the Thumbnail menu and display
the Main menu.
INPUT
Close the Thumbnail menu and display
the Input Selection menu.
Notes on Viewing JPEG Files
• TheTVignoresallcommandswhilereadingfiles.
Wait
for the completion message before continuing.
• Largefilesorhigh-capacitystoragedevicesmaytakea
long time to display. The screen will be blank while files
are read.
• Useonlyonesourcedeviceatatime.
USB Photo Menu Options
Start slide show. With the Slideshow icon high-
lighted, press
or
ENTER
.
Activate menu options.
Highlight an icon and press
ENTER
to:
• starttheslideshow
• displaypicturethumbnails
• opentheMedia Setup
submenu.
Display or close the
Main menu.
Press
MENU.
Display status for the
file source.
Press
INFO.
Select a different con-
nected device
1. Press
INPUT
.
2. Highlight the icon for a dif-
ferent device.
3. Press
ENTER
.
Clear status display
or menu to show the
USB Photo menu
Press
EXIT
.
IMPORTANT
Stop playback or change to a different TV input
before disconnecting from the USB photo port.
I
N
P
U
T
4
L-AUDIO-R
USB
VIDEO/Y
Pb
Pr
USB
L-AUDIO-R
0QUJPOBMBVEJP
EFWJDF
Media Setup Menu
Media Setup menu
In the Media Setup menu you can adjust the slide show
display, number of repetitions, or display interval.
• SelecteitherAuto or Manual advance. During
manual operation, press or
ENTER
to advance to
the next slide.
• Forautomaticadvance,selectthetimeintervalfor
display of each slide. The interval you select here is
the minimum time between slides; actual time may
be longer for larger files.
• Forautomaticadvance,selectthenumberoftimes
(frequency) to play the complete slide show: Once,
Twice, or Continuous.
• Press
EXIT
to close the Media Setup menu and
return to the USB Photo menu.
USB Photo Menu Compatible Picture Files
• Stillimagesrecordedondigitalcamerasusingthe
Exchangeable Image File Format, version 2.1 (EXIF
2.1) standard for digital still cameras and Design
Rules for Camera File Systems version 1.0 (DCF 1.0)
• Someimagesopenedandresavedonacomputer
may not play back or may not display in the thumb-
nail list. This happens if the files were resaved in an
incompatible format.
• Fullpathfilenamescanbenolongerthan50char-
acters and must end in a .jpg extension. Only the
first 20 of the 50 characters will display.
• Imagesonstoragedeviceswithacapacityofover
256 MB can take a longer initial time to display.
Photos and Moving Video as Composite
Video
Connect the camera to the TV using a composite video
cable if:
• YouareunabletoseeimagesusingtheUSBphoto
port.
•
You wish to view moving video from the camera.
The TV’s USB Photo menu will be unavailable and
you must control the slide show through the camera.
Display resolution is standard-definition (480i).
Refer to the owner’s manual supplied with the
1.
camera for instructions needed for this setup.
Set the camera’s output signal type to
2.
NTSC and
put the camera into playback mode.
With the camera still turned on, connect your digital
3.
camera’s composite video cable (usually yellow)
to the
VIDEO/Y
jack on the front of the TV. To hear
audio, connect the camera’s audio output cable to
the
AUDIO
L
jack.
When the
4.
Auto Input Sensing screen displays,
press
EXIT
or assign the name Camcorder.
Press
5.
INPUT
to display the Input Selection menu.
Highlight the icon for the camera input and press
6.
ENTER
.
If viewing photos, advance through the images manu-
7.
ally or set the camera to advance automatically.
L-AUDIO-R
USB
VIDEO/Y
Pb
Pr
I
N
P
U
T
4
L-AUDIO-R
VIDEO/Y
I
N
P
U
T
4
0QUJPOBM
"VEJP$BCMF
Camera connection using a composite video cable
Slide Show
Use these keys during the slide show:
Keys for JPEG Picture Slide Show
Begin or resume slide show playback
Pause or resume playback while in auto-
matic advance mode.
or
ENTER
Advance to the next slide.
Go to the previous slide.
F
ORMA
T Rotate the slide clockwise in 90˚ incre-
ments.
Stop slide show and display the USB Photo
menu.
INFO
Display status for the viewing device and
current image.
INPUT
Display the Input Selection menu.
MENU
Display or remove the TV Main menu.
Note: Always press (
STOP
) to stop slide show play-
back before disconnecting from the USB Photo
port.
IMPORTANT
The TV can read JPEG files as created by the
camera. If you edit a picture file on a computer
and resave the image, the TV may be unable to
read the resaved file.
Downloaded from www.Manualslib.com manuals search engine