Filter
Top Products
66 Appendices
Appendices 67
IMPORTANT
You may need to reprogram the remote
control after changing the batteries.
Programming the Remote Control
Move the slide switch at the top of the remote to
1.
the position for the product you want to control.
Refer to the table below. Only one of each device
type can be controlled in each slide-switch position.
Switch Position Affected Device
CABLE/SAT
Cable Box
DTV Receiver
Satellite Receiver
VCR
VCR
DVR
Laser Disc Player
DVD Player/Recorder
DVD
DVD Player/Recorder
DVR
Laser Disc Player
VCR
AUDIO
A/V Receiver
Audio Amplifier
CD Player
Press and hold
2.
POWER
on the remote control for
several seconds until the button blinks twice and
goes off.
Release the
3.
POWER
button.
Enter the first five-digit code listed for your equip-
4.
ment.
The •
POWER
button blinks twice when you start to
enter the code and then once for each addi-
tional keypress.
The •
POWER
button blinks twice when you finish
entering a valid code.
Move the slide switch to another position if you •
need to start over or wish to exit programming
mode.
Point the remote control at the equipment and
5.
press
POWER
. If the product has no power on/off
function, press a different key, such as (
PLAY
),
(
STOP
),
VOL
, or
MUTE.
If the equipment responds, the remote control •
is properly programmed to operate the equip-
ment.
If the equipment does not respond, repeat •
steps 2–4 with the next five-digit code listed for
your equipment.
Once you have found the correct code, write it in
6.
the space below for future reference.
Switch Position
Device Type Code
CABLE/SAT
VCR
DVD
AUDIO
Code Verification
To determine the code programmed for any position of
the slide switch:
Move the slide switch to the position you wish to
1.
verify.
Press and hold
2.
POWER
on the remote control for
several seconds until the button blinks twice and
goes off.
Press keys
3.
9 9 0
Press
4.
1
and count the blinks of the power button.
Write down the number of blinks as the first digit of
the code.
Repeat step 4 for the second, third, fourth, and fifth
5.
digits of the code.
Audio Lock: Universal A/V Receiver Control
With Audio Lock active, the remote control operates
the volume and mute functions of the A/V receiver in all
positions of the slide switch. Activate Audio Lock if you
normally use an A/V receiver with your TV and other
A/V equipment.
Program the
1.
AUDIO
position for your A/V receiver as
described earlier in this section.
With the slide switch in the
2.
AUDIO
position, press
and hold
POWER
on the remote control for several
seconds until the button blinks twice and goes off.
Press keys
3.
9 9 3 ENTER
The
POWER
button will blink twice to indicate Audio
Lock is active.
To Reset the Remote Control to Operate Volume
and Mute for the TV Speakers
Press and hold
1.
POWER
for several seconds until the
key blinks twice and goes off.
2. Press keys
2.
9 9 3 VOL
.
The
POWER
key will blink four times to indicate Audio
Lock has cleared.
Appendix C: Programming the Remote Control, continued
Programming Codes
Audio Amplifiers
Make
Code
Acurus
30765
Adcom
31100, 30577
Altec Lansing
31742
Aragon
30765
Bel Canto Design
31583
Bose
30674
Carver
30892
Cary Audio
Design
31879
Classe
31461
Curtis Mathes
30300
Durabrand
31561
Flextronics
31879
GE
30078
Halcro
31934
Harman/Kardon
30892
JVC
30331
Klipsch
30765
Krell
31837
Left Coast
30892
Lenoxx
31561
Lexicon
31802, 31145
Marantz
30892
Mark Levinson
31483
McIntosh
30251
Modulaire
30395
Mondial
30765
Optimus
30823, 30395, 30300,
30013
Parasound
31934
Philips
30892
Pioneer
30823, 30300, 30013
Polk Audio
30892
Primare
31395
RadioShack
30395
RCA
30823, 30300, 30013
Realistic
30013, 30395
Soundesign
30078
Technics
30372
Victor
30331
Wards
30078, 30013
Yamaha
30354
Cable Boxes
Make Code
A-Mark 10144, 10008
ABC 10237, 10014, 10011,
10008, 10007, 10003
Accuphase 10014, 10011, 10007,
10003
Acorn 10237
Action 10237
Active 10237
Americast 10899
Archer 10237
BCC 10276
Bell & Howell 10014
Bell South 10899
British Telecom 10003
Century 10008
Clearmaster 10883
Cable Boxes
Make Code
ClearMax 10883
Comtronics 10040
Cool Box 10883
Coolmax 10883
Digeo 11187
Digi 10637
Director 10476
Dumont 10637
Emerson 10014
Everquest 10040
Fosgate 10276
GC Electronics 10040
GE 10144
General Instru-
ment
10810, 10476, 10276,
10020, 10014, 10012,
10011, 10003
Gibralter 10003
GMI 10883
GoldStar 10144, 10040
Hamlin 10273, 10259, 10020
Hitachi 10011, 10008, 10003
Houston 10 011
Hytek 10007
Hytex 10007
Insight 10476, 10810
Jebsee 10014
Jerrold 10810, 10476, 10276,
10020, 10014, 10012,
10011, 10003
Memorex 10000
Mitsubishi 10003
Motorola 11376, 11254, 11187,
11106, 10810, 10476,
10276, 10014
Multitech 10883
Nova Vision 10008
Novaplex 10008
NSC 10637, 10012
Oak 10007
Pace 11877, 10877, 10237,
10008
Panasonic 10144, 10107, 10008,
10000
Panther 10637
Paragon 10525, 10008, 10000
Penney 10637, 10000
Philips 11305, 10317, 10259
Pioneer 11877, 10877, 10533,
10144
Prism 10012
Pulsar 10040, 10000
Pulser 10040
Quasar 10000
R-Line 10040
RadioShack 10883
RCA 1125 6
Regal 10279, 10276, 10273,
10259, 10020
Regency 10020
Rembrandt 10040, 10011
Runco 10000
Cable Boxes
Make Code
Samsung 10144, 10040, 10003
Scientific Atlanta 11877, 10877, 10477,
10237, 10012, 10008,
10003, 10000
Signal 10040, 10011
Signature 10011
SL Marx 10040
Sony 110 06
Sprucer 10144
Starcom 10014, 10003
Stargate 10040, 10014
Storm 10637
Supercable 10276
Supermax 10883
Teleavia 10040
Teleview 10040
Thomson 1125 6
Timeless 10040
Tocom 10012
Torx 10003
Toshiba 10000
Tristar 10883
TV86 10040
United Artists 10007
United Cable 10276, 10014, 10011,
10003
US Electronics 10276, 10008, 10003
V2 10883
Videoway 10000
Viewmaster 10883
Vision 10883
Vortex View 10883
Zenith 10899, 10525, 10000
CD Players
Make Code
Acoustic
Research
30420
Aiwa 30157
Akai 30083
Arcam 30157
Audio Pro 30437
Audio Research 30157
Burmester 30420
Cairn 30157
California Audio
Labs
30303, 30029
Cambridge
Soundworks
30157
Carver 30437, 30179, 30157
Cary Audio
Design
31876
Classic 31297
Curtis Mathes 30032
Denon 30766, 30034, 30003
DKK 30000
DMX Electronics 30157
Fisher 31325, 30179, 30000
Garrard 30420
Genexxa 30032
GPX 31296
Appendix C: Programming the Remote Control, continued
Downloaded from www.Manualslib.com manuals search engine