Mitsubishi Electronics WD-52725, WD-62525, WD-52525, WD-62725 Projection Television User Manual


 
24
25
DTV Connectors and Adaptors
Figure 11
The TV back panel has 5 RCA-type connectors for
the Input-DTV. The back panel of your external DTV
receiver may use RCA-type connectors or BNC-type
connectors. If your DTV receiver comes with BNC
type connections, you will need to purchase BNC to
RCA adaptors to connect the TV to the DTV receiver.
These adaptors should be available at most electronic
supply stores.
RCA
Connector
or
BNC to
RCA BNC
Adaptor Connector
Adaptor
Fitted to
Connection
See Appendix B for component video
signal compatibility information.
For digital audio connections, see your
DTV Receiver and A/V receiver Owner’s
Guides.
IMPORTANT
Figure 11. DTV Connectors and Adaptors
DTV Connectors and Adaptors Connecting a DTV Receiver with
Component Video
IREMITTER
NetCommand
R
INPUT-1
AUDIO2
AUDIO/VIDEO1
AUDIO
L(MONO)R
INPUT-2
COMPONENT-1
YPbPr(480i/480p/720p/1080i)
Y/G
Pb/BPr/R
COMPONENT-2
YPbPr(480i/480p/720p/1080i)
INPUT-DTV
YPbPr/RGBHV
(480i/480p/720p/1080i)
DTV/
CABLE/
VHF/
UHF
ANT-2
AUX
ANT-1
MAIN
DIGITAL
AUDIO
PC
VGA/SVGA/XGA/
720p
60Hz
PC-
AUDIO
PC-
INPUT
M-LINK
CONTROL/
RS-232C
HDMI
M-LINK
IEEE1394
INPUT/OUTPUT
VIDEO S-VIDEO
MONITOR
OUTPUT
L
R
V H
CARD
TOP
CableCARDSLOT
TM
DTV Receiver (with YPrPb connections)
V
I
D
E
O
Y
P
r
P
b
S
-
V
I
DE
O
V
C
R
C
O
N
TR
O
L
P
H
O
NE
J
A
CK
R
F
R
E
M
O
T
E
O
U
T
TO
T
V
C
H
3
C
H
4
C
A
U
T
I
O
N
R
I
S
K
O
F
E
L
E
C
T
R
I
C
A
L S
H
O
C
K
D
O
N
O
T
O
P
E
N
D
I
G
I
T
A
L
A
U
D
I
O
O
UT
White
Red
Incoming
Antenna
or Cable
SATELLITE IN
IN FROM ANT
or
to antenna,
cable or satellite
A
U
D
I
O
L
R
A
U
D
I
O
L
R
V
I
DE
O
TV back panel
1.
2.
2.
4.
1.
3.
4.
w
h
i
t
e
R
e
d
DVI
AnalogAudio
L
R
AUDIO
L(MONO)R
3.
Figure 12. Connecting an External DTV Receiver with
Component Video Connections
DTV Receiver with Component Video
Figure 12
A coaxial splitter, RCA component video cables and audio
cables are required. These are not included with the TV.
1. Connect the outside antenna, cable or satellite to
ANT or SATELLITE IN on the DTV receiver (see your
DTV receiver’s owner’s guide for instructions and
cable compatibility).
2. Connect the incoming terrestrial antenna or cable
(not satellite) to ANT-1 on the TV back panel
(a coaxial splitter, available at most electronic
supply stores, may be required to complete this
installation).
3. Connect RCA-type cables from the YPrPb outputs
on the DTV receiver to Input-DTV on the TV back
panel, matching the correct connections:
DTV Receiver to TV Back panel
Y to Y
Pr to Pr
Pb to Pb
4. Connect the L (left) and R (right) audio cables from
the DTV receiver to Input-DTV AUDIO on the TV
back panel.
Note: To utilize the benefits of a digital A/V
receiver, connect your DTV receiver’s digital audio
out to a digital input on your digital A/V receiver.