Filter
Top Products
Functional overview
Before you start
8
Front Panel
1. Disc tray
Place a disc when open.
2. Display
Refer to “Front Panel Display Guide” on page 12.
3. OPEN/CLOSE A button*
Hit to open or close the disc tray.
4. CHANNEL L / K button
Press to change the channel up and down.
5. REV E button
During playback, hit to skip to the previous chapter
or track.
During playback, press and hold for 1.5 seconds to fast reverse.
When playback is paused, hit repeatedly to slow reverse.
6. FWD D button
During playback, hit to skip to the next chapter or track.
During playback, press and hold for 1.5 seconds to
fast forward.
When playback is paused, hit repeatedly to slow forward.
7. STOP C button*
Hit to stop play or recording.
8. PLAY B button*
Hit to start or resume play.
9. POWER button
Hit to turn the unit on and off.
If timer programmings have been set, hit to set the
unit in timer-standby mode.
10. AUDIO input jacks (LINE2)
Use to connect external equipment with standard
audio cables.
11. VIDEO input jack (LINE2)
Use to connect external equipment with a standard
video cable.
12. S-VIDEO input jack (LINE2)
Use to connect the S-Video output of external equip-
ment with an S-Video cable.
13. REC/OTR button
Hit once to start a recording. Hit repeatedly to start
a one-touch Timer Recording.
14. REC SPEED button
Hit to switch the recording speed.
15. Remote control sensor
Receive signals from your remote control so that you
can control the unit from a distance.
Rear Panel
ANTENNA
AUDIO IN
VIDEO IN
L
R
AUDIO OUT
VIDEO OUT
(L1)
IN
IN
OUT
OUT
S-VIDEO
COMPONENT
VIDEO OUTPUT
L
Y
P
B
/C
B
P
R
/C
R
R
DIGITAL AUDIO OUTPUT
PCM / BITSTREAM
COAXIAL
1
23 4
5678910
11
1. ANTENNA IN jack
Use to connect an antenna.
2. VIDEO IN jack (LINE1)
Use to connect external equipment with a standard video cable.
3. VIDEO OUT jack
Use to connect a TV monitor,AV receiver or other
equipment with a standard video cable.
4. AC Power Cord
Connect to a standard AC outlet to supply power to this unit.
5. COAXIAL DIGITAL AUDIO OUTPUT jack
Use to connect an AV receiver, Dolby Digital decoder
or other equipment with a coaxial digital input jack
with a digital coaxial cable.
6. AUDIO OUT jacks
Use to connect a TV monitor,AV receiver or other
equipment with standard audio cables.
7.
COMPONENT VIDEO OUTPUT jacks
Use to connect a TV monitor with component video
inputs with component video cables.
8. S-VIDEO OUT jack
Use to connect the S-Video input of a TV monitor,AV
receiver or other equipment with an S-Video cable.
9. S-VIDEO IN jack (LINE1)
Use to connect the S-Video output of external equip-
ment with an S-Video cable.
10. AUDIO IN jacks (LINE1)
Use to connect external equipment with standard
audio cables.
11. ANTENNA OUT jack
Use to connect an antenna cable to pass the signal
from the TV ANTENNA IN to your TV monitor.
Note
• Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to
the unit.
• This unit does not have the RF modulator
.
REC/OTRREC SPEED
OPEN/CLOSE CHANNEL REV FWD STOP PLAY POWER
S-VIDEO VIDEO AUDIO
L R
8* 9
1211 101314
15
1
23*4567*
(
*
) The unit can also
be turned on by
pressing these
buttons.
E6700UD_EN/SP.qx3 04.12.25 0:58 PM Page 8