Filter
Top Products
30
RQT8859
Timer recording
See also “Important notes for recording” (➡ 8).
Depending on the type of disc used for recording or the type of
broadcast, there may be restrictions on the title you are trying to
record.
[HDD] [RAM] [-R] [-RW‹V›] [+R] [+RW]
≥You can enter up to 32 programmes up to a month in advance.
(Each daily or weekly programme is counted as one programme.)
[RAM] [-RW‹V›] [+R] [+R]DL] [+RW]
≥To use a new disc, formatting is necessary.
Preparation
≥Turn on the television and select the appropriate video input to suit
the connections to this unit.
≥If recording to DVD, insert a disc that you can use for recording
(➡ 24).
≥Make sure that the clock settings are correct (➡ 73).
Entering G-
CODE numbers is an easy way of timer recording. You can
find these numbers in TV listings in newspapers and magazines.
[Note]
The G-
CODE system is not supported for digital broadcasts.
1 Press [G-Code].
2 Press the numbered buttons to enter
the G-CODE number.
Press [2] to move back to correct a digit.
3 Press [OK].
≥Confirm the programme (start and end time) by using a TV
magazine, etc. and make corrections if necessary using
[3, 4, 2, 1] (➡ 31, step 3).
≥When “-- ---” appears in the “Name” column, you cannot set
timer recording. Press [3, 4] to select desired programme
position. After you have entered the information of a TV
station, it is kept in the unit’s memory.
4 Press [OK].
The timer programme is stored and the timer icon is
displayed.
“F” lights on the unit’s display to indicate timer recording
standby has been activated.
Repeat steps 1–4 to programme other recordings.
Press [Í DVD] to turn the unit off.
∫ To cancel recording when recording has already
begun (➡ 32)
∫ To release the unit from recording standby
(➡ 32)
∫ Notes on timer recording (➡ 32)
G-CODE is a registered trademark of
Gemstar Development Corporation. The
G-
CODE system is manufactured under
license from Gemstar Development
Corporation.
STATUS
REC MODE
REC
MANUAL SKIP
CREATE
CHAPTER
F
U
N
C
T
I
O
N
M
E
N
U
D
I
R
E
C
T
N
A
V
I
G
A
T
O
R
G
U
I
D
E
RETURN
PLAY/x1.3
PAUSE
STOP
SLOW/SEARCH
SKIP
CH
PAG E
SELECT
INPUT
0
9
8
7
6
54
3
2
1
CH
AV
Í
TV
DRIVE
SELECT
Í
DVD
VOL
DELETE
EXIT
OK
OPTION
ANALOGUE
CH
G-Code
AUDIO
DISPLAY
TIME SLIP
PROG/CHECK
G-Code
3,4,2,1
OK
DRIVE
SELECT
REC MODE
Í DVD
PROG/CHECK
Numbered
buttons
“Blue”
Using G-CODE system to make timer
recordings
G-Code
Record
1:58 SP
DVD
30:24 SP
HDDRemain
12:53:00 15. 7. TUE
Input G-Code Number 0-9, and press OK.
G-Code
Record
1:58 SP
DVD
30:24 SP
HDDRemain
12:53:00 15. 7. TUE
Input G-Code Number 0-9, and press OK.
Timer
Recording
1:58 SP
DVD
30:24 SP
HDDRemain
12:54:00 15. 7. TUE
Mode
StopStartName Date
HDD
DVD
20:0019:0015. 7. TUE SPHDD
2A ARD
Programme Name
All Services : ARD
No.
Name
ARD
01
&
Timer icon
12:56:00 15. 7. TUE
Mode
Stop
HDD
DVD
HDD
Drive
space
SP
OK
20:00
Programme
Check to make sure “OK”
is displayed (➡ 33).
EX77_87GN.book Page 30 Wednesday, May 30, 2007 1:10 PM