Filter
Top Products
Reference
60
VQT0R73
On the unit’s display Page
On the TV Page
On the unit’s display Page
On the TV Page
Error messages
∫ Common
H, F, U
(“” stands for a number.)
≥An error has occurred. The number following “H”, “F” or “U” depends on the status of the unit.
Reset procedure: (“The unit is on but cannot be operated.” l 62)
≥
If the service numbers fail to clear, note the service numbers and contact a qualified service person.
–
–
∫ DVD
Cannot finish recording
completely.
≥The program was copy-protected.
≥The disc may be full.
≥There are already 99 recorded titles ([+R] 49 recorded titles).
–
–
–
Cannot play. ≥You inserted an incompatible disc (Discs recorded in PAL video, etc.). –
Cannot record on the disc. ≥The disc may be dirty or scratched. 8
Unable to format.
Please check the disc.
Cannot record. Disc is full. ≥Create space by erasing any unwanted titles. [RAM] [-RW‹V›]
[Even if you erase recorded content from the DVD-R or +R, there is no increase in disc space. Available
disc space on DVD-RW (DVD-Video format) increases only when the last recorded title is erased.]
≥Use a new disc.
21, 30,
33
–
Cannot record. The number
of titles has exceeded the
maximum limit.
Error has occurred. Please
press ENTER.
≥Press [ENTER] to start recovery process. You cannot operate the unit while it is recovering
(“SLF CHECK” appears on the unit’s display).
–
No disc ≥You haven’t inserted a disc. Correctly insert a disc that the unit can play.
≥The disc is upside down. If it is a single-sided disc, insert it so the label is facing up.
6, 8
8
Please change the disc. ≥There may be a problem with the disc. Press [<, OPEN/CLOSE] to remove it and check it for
scratches or dirt. (The unit turns off automatically after you open the tray.)
8
This is a non-recordable disc. ≥The unit cannot record on the disc you inserted. Insert a DVD-RAM or unfinalized DVD-R, DVD-
RW (DVD-Video format) or +R.
≥You inserted an unformatted DVD-RAM or DVD-RW. Format the disc with the unit.
–
31
This disc is not formatted
properly.
≥The operation is prohibited by the unit or disc. 20
RC
(“” stands for a number.)
≥The remote control and main unit are using different codes. Change the code on the remote
control.
18
Err ≥The disc is dirty or badly scratched. The unit cannot record, play, or edit.
≥You have used a lens cleaner and it has finished. Press [<, OPEN/CLOSE] to eject the disc.
≥You have inserted a disc the unit cannot play or record on.
≥You have inserted a DVD-RAM or DVD-RW that is unformatted or recorded on other equipment.
≥
If there is no change after turning the unit on and off, consult the dealer where the unit was purchased.
8
8
7
31
–
oooooo
(self check)
≥There was something unusual detected with the disc while recording, playing or transferring
(dubbing), there was a power failure or the AC plug was disconnected while the unit was on. The
unit is carrying out its recovery process. This process restores the unit to normal operation. The
unit is not broken. Wait until the message disappears.
The symbol “o” appears at the bottom left of the unit’s display. The
number of symbols increases one by one until six appear. They then
disappear one by one until none remain. This continues during self
check.
61
U59 ≥The unit is very warm.
The unit switches to standby for safety reasons. Wait for about 30 minutes until the message disappears.
Select a position with good ventilation when installing the unit. Do not block the cooling fan on the
rear of the unit.
–
U99 ≥The unit fails to operate properly. Press [POWER Í/I] on the main unit to switch the unit to
standby. Now press [POWER Í/I] on the main unit again to turn the unit on.
–
∫ VHS
No VHS cassette. ≥A video cassette is not inserted when recording programs. Insert a video cassette with an
accidental erasure prevention tab.
46
Please check write protect
tab on the VHS cassette.
≥
A video cassette without the accidental erasure prevention tab is inserted when recording programs.
Use a video cassette with an accidental erasure prevention tab.
46
VHSDVD
ES40VP&PC.book 60 ページ ２００５年９月６日 火曜日 午前１０時２３分