Filter
Top Products
Setting the Remote Control to Operate a Cable Box/DSS Receiver 27
CABLE BOX/DSS RECEIVER CODES
GENERAL INSTRUMENTS . . 01, 02, 03, 04, 05, 06, 07
HAMLIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21, 22
JERROLD . . . . . . . . . . . . . . . . 01, 02, 03, 04, 05, 06, 07
OAK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 17, 18
PANASONIC . . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 20
PIONEER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 12
SCIENTIFIC ATLANTA. . . . . . . . . . . . . . . . . 08, 09, 10
TOCOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23, 24, 25
ZENITH . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13, 14, 15
MAGNAVOX DSS . . . . . . . . . . . . . . . . . . . . . . . 42, 43
RCA DSS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40, 44
SONY DSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4
Try step 1 again. If the remote control works your Cable Box
or DSS Receiver, you’re finished. If the remote control still does
not work your Cable Box or DSS Receiver, repeat steps 2 - 3
using a different code.
• If you had to program the remote
control to operate your Cable Box or
DSS Receiver, whenever you replace
the batteries in the remote control,
you must program the remote con-
trol again.
• The remote control may only oper-
ate some features of your Cable
Box or DSS Receiver.
• Some Cable Boxes/DSS Receivers
can only be turned on at the Cable
Box/DSS Receiver.
Helpful Hints
There is no guarantee that the remote
control will operate your Cable Box or
DSS Receiver.
Your VCR remote control may operate your Cable Box or DSS
Receiver. Follow these steps to set the remote control code.
1
Point the remote control at your Cable Box/DSS
Receiver. Press the CBL/DSS button, then the POWER
button. If your Cable Box/DSS Receiver turns on or off, try the
CHANNEL Up/Down buttons. If your Cable Box/DSS Receiver
does not turn on or off, or if the CHANNEL Up/Down buttons
don’t work, go to step 2.
2
Find the brand of your Cable Box/DSS Receiver on the
list below and remember the two-digit number to the
right of it.
3
Press the MUTE button, then press the CBL/DSS button.
Use two Number buttons to enter the two-digit code for
your Cable Box or DSS Receiver. For example, if you have a
Zenith Cable Box, press Number buttons 1, 3.
...
...
POWER
CBL/DSS
VCR TV
EJECT MUTE
MENU
EXIT/STATUS
CLEAR
VCR PLUS+
/ENTER
LIGHT
F.ADV
PAUSE/STILL
1 2 3
4 5 6
7 8 9
100 0
GO-TO
MEMORY
INDEX
VAR. SLOW
REMOTE LOCATOR
SKIP
VCR/TVSPEED
SEARCH
SLOW
TRACKING
STOP
REW FF
PLAY
VOL CHANNEL
/OTR
REC
1
2
Find the code for your Cable
Box/DSS Receiver.
4
Repeat step 1.
3