Filter
Top Products
47
En
07
Changing the speaker setup
Set whether or not speakers are connected to an AV
receiver or amplifier, etc., their size and their crossover
frequency. This setting is only valid for the AUDIO OUT
terminals.
When there are no speakers whose speaker size is set to
Small, select Bypass for the crossover frequency.
When there are speakers whose speaker size is set to
Small, select the crossover frequency (Bypass cannot be
selected).
Caution
•The Speaker Setup cannot be selected when Audio
Output Mode is set to 2 Channel. Change the
setting to Multi-channel (page 43).
1
Sele
ct and set Speakers Speaker Setup Next
Screen.
Use / to select, then press ENTER.
2 Select the speaker and change the setting.
Use / to select, then use / to change the setting.
• L/R (front left and right speaker s): Large/Small
• C (center speaker): Large/Small/None
• SL/SR (left and right surround speakers): Large/
Small/None
• SBL/SBR (left and right surround back speakers):
Large/Small/None
• SW (subwoofer): Yes/No
• Crossover: Bypass/50 Hz/80 Hz/10
0 Hz/150 Hz
Note
•D
epending on the combination of settings of the
different speakers, the settings of speakers other than
the one you have changed may also change
automatically.
•When a subwoofer with a filter bypass function is
connected and there is no speaker whose speaker
size is set to Small, if the subwoofer’s filter is set to be
bypassed, the player’s high precision digital filter is
used. In this case, set the crossover frequency to
something other than Bypass.
•Upon purchase, the crossover frequency is set to
Bypass.
Adjusting the distance of the
different speakers
Adjust the distance between you and the different
speakers. This setting is only valid for
the
AUDIO OUT
terminals
.
Caution
• This cannot be selected when Audio Output Mode
is set to 2 Channel. Change the setting to Multi-
channel (page 43).
• Speaker Distance of the speakers set to None or No
at Speaker Setup cannot be adjusted (above).
1 Select and set Speakers Speaker Distance
Next Screen.
Use / to select, then press ENTER.
2 Select the speaker and adjust the distance.
Use / to select, then use / to adjust.
• The distance of all the speakers can be set to between
1 inch and 45 feet, in units of 1 inch.
Adjusting the output level of the
different speakers (Channel Level)
Adjust each output level of the different speakers by using
test tones.
This setting is only valid for the AUDIO OUT
terminals.
Caution
• This cannot be selected when Audio Output Mode
is set to 2 Channel. Change the setting to Multi-
channel (page 43).
• Channel Level of the speakers set to None or No at
Speaker Setup cannot be adjusted (above).
• Test tones are output. Lower the volume of the device
connected to the player.
1 Select and set Speakers Channel Level, then
Fix or Variable.
Use / to select, then press ENTER.
• Fix – The output level of all the speakers is set to the
maximum.
• Variable – The output level of all the speakers is set
6.0 dB lower than when Fix is selected. From this
point, the output levels of the L, C, R, SL, SR, SBL, SB
R
and SW speake
rs can be adjusted within the range of
–6.0 dB to +6.0 dB.
If you have selected Variable, proceed to step 2.
L/R
C
SL/SR
SBL/SBR
SW
Large
Large
Large
Large
Yes
Crossover
Bypass
Speaker Setup
BD PLAYER
L
C
R
SR
SBR
SBL
SL
SW
Speaker Distance
BD PLAYER
10’00”
10’00”
10’00”
10’00”
10’00”
10’00”
10’00”
10’00”
V6000_CUXJ_EN.book 47 ページ ２００９年６月５日 金曜日 午前１１時５７分