Sharp LC42SB45U Flat Panel Television User Manual


  Open as PDF
of 27
 
13
Next
Language
English
Français
Español
Previous
TV Setup 1/4
Next
NextEXIT
Previous
TV Setup 2/4
If you are connecting the TV to a High
Definition Cable box or Satellite Receiver,
you will only need to tune your TV to the
input signal source connected. Use the
INPUT button to select your inputs.
Option 1 Option 2
If you are connecting your TV to
Air or Cable signal from the
wall outlet, use the 75 Ohm
connector on the back of the TV.
Refer to the user manual for additional
connections.
Auto ProgramAuto Program
Exit Next
POWER
Turning On/Off the Power
POWER
(On/Standby)
PressPOWERontheTV,or POWERontheremotecontrolunittoturn
thepoweron.
• POWERindicator(Green):TheTVison.(Afterafewseconds,awindow
appearswithsound.)
PressPOWERontheTV,orPOWERontheremotecontrolunitagain
toturnthepoweroff.
• TheTVentersstandbyandtheimageonthescreendisappears.
• POWERindicator(Red):TheTVisstandby.
• IfyouarenotgoingtousethisTVforalongperiodoftime,besuretoremove
theACcordfromtheACoutlet.
• WeakelectricpowerisstillconsumedevenwhentheTVisturnedoff.
• Ifthereisnosignalinputfor30minutes,thepowerwillturntostandbymode
automatically.
Watching TV
Initial Setup
WhenyouturnontheTVforthersttime,itwill
automaticallymemorizethebroadcastingchannels
availableintheregionwhereyoulive.Performthe
followingstepsbeforeyoupressPOWERonthe
remotecontrolunit.
1. Insertthebatteriesintotheremotecontrolunit.(Seepage8.)
2. ConnecttheantennacabletotheTV.(Seepage8.)
3. PlugintheACcordtotheACoutlet.(Seepage7.)
Language (Language setting)
Selectfromamong3languages:English,FrenchandSpanish.
1
Press
a
/
b
toselectthedesiredlanguagelistedonthe
screen,andthenpresstheBbutton.
• Autoprogrammingmaytakeupto20minutestocomplete.
DigitalchannelswilltakelongerthanAnalogtondand
program.PleasewaituntilyouseetheAutoprogramming
completemessage.TheTVwillthenswitchautomatically
totherstchannelfound.
2
IfyouareconnectingtoaHDcablebox,presstheA
buttontoexit.IfyouareconnectingtoAntennaorCable
fromwalloutlet,presstheBbuttontonextstep.
NextExit Previous
TV Setup
Make sure that you have attached
your Air or Cable signal into
the jack on the back of your TV
that is labeled 75 Ohm.
Now select either Air or Cable,
using the cursor up/down buttons
on the remote. Once you have
made your selection, press the
GREEN Next button to proceed.
Air
Cable
3/4
Exit Previous
TV Setup 4/4
System searching. Please wait...
Analog channels found: 5
Digital channels found: 5
Auto programming may take up to 20 minutes to complete. Digital channels
will take longer than Analog to find and program. Please wait until you see the
Auto Programming complete message. The TV will then switch automatically
to the first channel found.
Finish
TV Setup 4/4
Channel search completed.
Analog channels found: 10
Digital channels found: 10
Air/Cable (Antenna setting)
MakesurewhatkindofconnectionismadewithyourTV
whenselecting"Air"or"Cable".
3
Press
▲
/
▼
toselect"Air"or"Cable".
PresstheBbuttontocontinue.
4
PresstheAbuttontonish.
 previous next