Filter
Top Products
52
E
Specications
n
Product Specications
Model PN-E702
LCD component
70" Class [69-1/2 inch (176.6cm) diagonal] TFT LCD
Max. resolution (pixels)
1920 x 1080
Max. colors
Approx. 1.06 billion colors
Pixel pitch
0.802 mm (H) × 0.802 mm (V)
Viewing angle
176° right/left/up/down (contrast ratio ≥ 10)
Screen active area inch (mm)
60-9/16 x 34-1/16 (1538.9 x 865.6)
Computer input signal
Digital (DVI 1.0 standard-compliant), Analog RGB (0.7 Vp-p) [75
Ω
]
Sync signal
Horizontal/vertical separate (TTL: positive/negative), Sync-on-green,
Composite sync (TTL: positive/negative)
Video color system
NTSC (3.58MHz)/NTSC (4.43MHz)/PAL/PAL-60/SECAM
Plug and play
VESA DDC2B
Power management
VESA DPMS, DVI DMPM
Input terminals
PC/AV
Digital
HDMI x 1
PC
Analog
Mini D-sub 15 pin, 3 rows x 1
Audio
3.5 mm mini stereo jack x 1
Serial (RS-232C)
D-sub 9 pin x 1
When PN-ZB01
(optional) is
attached
PC/AV
Digital
DVI-D 24 pin (HDCP compatible) x 1
PC
Analog
BNC
*
1
*
2
x 1
AV
Composite video
BNC x 1
S-video
x 1
Component BNC (Y, Cb/Pb, Cr/Pr) *
1
x 1
Audio
RCA pin (L/R) x 2
Output terminals
Audio
RCA pin (L/R) x 1
Serial (RS-232C)
D-sub 9 pin x 1
When PN-ZB01
(optional) is
attached
PC/AV
Digital
DVI-D 24 pin x 1
External speaker 7 W + 7 W
[6
Ω
]
LAN terminal
[
When PN-ZB01 (optional) is attached
]
10 BASE-T/100 BASE-TX
Speaker output 7 W + 7 W
Power requirement AC 100 V - 240 V, 2.8 A, 50/60 Hz
Operating temperature
*
3
32°F to 104°F (0°C to 40°C)
Operating humidity 20% to 80% (no condensation)
Power consumption
(Maximum / input signal waiting mode
*
4
/ standby
mode
*
5
)
235 W / 1.0 W / 1.0 W
Power consumption
[
When PN-ZB01 (optional) is attached
]
240 W
Dimensions (excluding protrusions) inch (mm)
Approx. 63-9/16 (W) x 3-15/16 (D) x 37-5/16 (H) (1,615 x 100 x 947)
Weight lbs. (kg)
Approx. 110.2 (50)
Weight [PN-ZB01 (optional)] lbs. (kg)
Approx. 1.102 (0.5)
*1 Cannot be used simultaneously.
*2 Does not support plug and play.
*3 Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP.
In such cases, please check the temperature condition specied by the optional equipments.
*4 When AUTO INPUT CHANGE is set to OFF.
*5 When STANDBY MODE is set to STANDARD. When STANDBY MODE is set to LOW POWER: 0.5 W
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specication changes for product improvement
without prior notice. The performance specication gures indicated are nominal values of production units. There may be some deviations from
these values in individual units.