Tascam DR-70D VCR User Manual


 
TASCAM DR-70D
37
10 – Messages
The following is a list of the pop-up messages.
Refer to this list if one of these pop-up messages appears on
the DR-70D and you want to check the meaning or determine a
proper response.
Message Meaning and response
Battery Empty
The batteries are almost out of power.
Replace the batteries.
Card Error
The SD card could not be recognized
properly. Change the card.
Card Full
The SD card has no remaining space.
Erase unnecessary files or move them
to a computer to make open space.
File Full
The total number of folders and files
exceeds the limit of 5000. Erase unnec-
essary folders and files or move them
to a computer.
File Not Found
A file cannot be found or a file might
be damaged. Please check that file.
File Not Found
Make Sys File
The system file is missing. This unit
requires a system file for operation.
When this message appears, press the
DATA dial to automatically create a
system file.
File Protected
The file is read only and cannot be
erased.
Format Error
Format CARD
The SD card is not formatted properly
or the card is broken. This message
also appears if the card was formatted
using a computer connected by USB
or if an unformatted card is inserted in
the unit.
Always use the DR-70D to format cards
to be used with it. Change the card or
press the DATA dial while this message
is being shown to format the card.
Formatting will erase all the data on
the SD card.
Invalid Card
Change Card
Something might be wrong with the
SD card. Change the SD card.
Invalid SysFile
Make Sys File
The system file required to operate
this unit is invalid. When this message
appears, press the DATA dial to
automatically create a new system file.
Layer too Deep
Folders can be created down to two
layers. You cannot create a new folder
inside the current folder.
MBR Error Init CARD
The SD card is not formatted properly
or the card is broken. Change the
card or press the DATA dial while this
message is being shown to format the
card.
Formatting will erase all the data on
the SD card.
No Card
No SD card is loaded in the unit. Insert
a recordable SD card.
No PB File
There is no file that can be played
back. The file might be damaged.
Non-Supported
The audio file is not a supported
format. Please see “7 – Connecting
with a Computer” for file formats that
this unit can use.
Switched To Internal
Battery
The power source has switched from
USB bus power to the batteries in the
unit.
Write Timeout
Writing to the SD card timed out.
Backup files on the card to a computer,
and format the card.
No Rec Channels
Selected
No recording channels have been
selected (all are off).
Message Meaning and response
Not Possible
Check FILE TYPE
The setting cannot be changed.
Change the
FILE TYPE
setting to
MONO or STEREO.
Not Possible
Check INPUT3/4
The setting cannot be changed.
Change the
INPUT 3/4
setting to
XLR/TRS.
Not Possible
Check Rec Chs
The setting cannot be changed.
Check the recording channels.
Not Possible
Set DUAL-REC OFF
The setting cannot be changed.
Turn DUAL REC mode off.
Can't Save Data
If any of these errors occurs, turn the
unit’s power off and restart it.
If the power cannot be turned off,
remove the batteries and disconnect
the AC adapter (TASCAM PS-P515U) or
disconnect the USB cable if using USB
bus power.
If the error message continues to
appear frequently, please contact a
TEAC Repair Center (See back cover).
Device Error
File Error
Not Continued
Player Error
Remote Cmd
Remote Rx
Writing Failed
Sys Rom Err
System Err 50
System Error 1
System Error 2
System Error 3
System Error 4
System Error 5
System Error 6
System Error 7
System Error 8
System Error 9